Husqvarna 326C, 326L, 326LS, 326LX-Series, 326LDX-Series, 326Lx manual Fitting the trimmer head

Page 11

ASSEMBLY

Fitting the trimmer head

WARNING!

! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury.

WARNING! Never use a cutting attachment

!without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury.

Fitting a trimmer guard and Superauto II 1" trimmer head

(326L, 326Lx, 326LDx)

LK

G

K F

I B

J C

I

A

Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L).

Fit the drive disc (B) on the output shaft.

Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

Insert the locking pin (C) in the hole to lock the shaft.

To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows:

Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half

(K). Pull apart the trimmer head, grasping the cover firmly.

Place the cover (I) and the support flange (F) on the output shaft.

Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible.

To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

To dismantle, follow the instructions in the reverse order.

Fitting other guards and cutting attachments

(326L, 326Lx, 326LDx)

Fit the correct trimmer guard (A) for use with the trimmer head.

Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L).

Fit the drive disc (B) on the output shaft.

Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

Insert the locking pin (C) in the hole to lock the shaft.

Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

H

H

To dismantle, follow the instructions in the reverse order.

English – 11

Image 11
Contents 326C 326L 326LX-SERIES Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what? What is WHAT?Personal protective equipment General Safety PrecautionsMachine′s safety equipment Cutting attachment guard Stop switchThrottle lock Muffler Vibration damping systemTrimmer head Cutting equipmentLocking nut Assembling and dismantling the two-piece shaft AssemblyAssembly Fitting the loop handleFitting other guards and cutting attachments Fitting the trimmer headGuard Fitting the trimmer guard and trimmer headFuel Fuel safetyFuel Handling Mixing FuelingStarting Starting and StoppingCheck before starting Starting and stoppingStopping Basic working techniques Basic safety rulesWorking Techniques General working instructionsClearing Carburetor MaintenanceHigh speed jet H Fine adjustment of the idle speed TCorrectly adjusted carburetor MufflerTwo-piece shaft Cleaning the air filterCooling system Spark plugBevel gear Oiling the air filterMaintenance Maintenance scheduleTechnical data Technical DataAttachments Art No Use with Your Warranty Rights and Obligations Federal Emission Control Warranty StatementTrimmy Hit Junior Trimmy T25 T25C 2,4 mm 079-0.095 75 m x Clic Trimmy H Click Trimmy Hit Pro Super Auto Super Auto II S35 25 m ´z+HAo¶5¨ T35 1140337-95 ´z+HAo¶5¨ ´z+HAo¶5¨