Husqvarna 323RJ, 325RJX-Series Muffler, Fine adjustment of the idle speed T, High speed jet H

Page 20

MAINTENANCE

Fine adjustment of the idle speed T

Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate.

IMPORTANT! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

High speed jet H

The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds.

Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly.

H

Note that the engine should not be under load when you adjust the high speed jet H. You should therefore remove the cutting attachment, nut, support flange and drive disc before adjusting the high speed jet H.

The high speed jet H is adjusted correctly when the machine burbles a little. If the machine races then the setting is too lean. If the engine produces a lot of smoke and burbles a lot then the setting is too rich.

CAUTION! For optimum adjustment of the carburettor, contact a qualified dealer/service workshop that has a revolution counter at their disposal.

Correctly adjusted carburettor

When the carburettor is correctly adjusted the machine will accelerate without hesitation and burble a little at maximum speed. It is also important that the cutting attachment does not rotate at idle. If the low speed jet L is set too lean it may cause starting difficulties and poor acceleration.

If the high speed jet H is set too lean it will result in less power, less performance, poor acceleration and/or damage to the engine.

If both the L and H jets are set too rich it will results in acceleration problems or too low a working speed.

Muffler

CAUTION! Some mufflers are fitted with a catalytic converter. See chapter on Technical data to see whether your machine is fitted with a catalytic converter.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. This is best done with a wire brush.

On mufflers without a catalytic converter the mesh should be cleaned weekly, or replaced if necessary. On mufflers fitted with a catalytic converter the mesh should be checked, and if necessary cleaned, monthly. If the mesh is damaged it should be replaced.

If the mesh is frequently blocked, this can be a sign that the performance of the catalytic converter is impaired. Contact your dealer to inspect the muffler. A blocked mesh will cause the machine to overheat and result in damage to the cylinder and piston. See also instructions under the heading Maintenance.

CAUTION! Never use a machine with a defective muffler.

WARNING! Mufflers fitted with catalytic

!converters get very hot during use and remain so for some time after stopping.This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of fire!

20 – English

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 323RJ 325RJX-series KEY to Symbols SymbolsContents Personal protective equipment Safety InstructionsMachine′s safety equipment Vibration damping system MufflerCutting equipment Locking nutNever use a machine that has a faulty muffler Safety Instructions Trimmer head Cutting equipmentSharpening grass cutters and grass blades General safety precautions Fuel safetyStarting Transport and storageBasic safety rules Grass clearing using a grass bladeGeneral working instructions Basic working techniquesGrass trimming using a trimmer head and plastic blades TrimmingWhat is WHAT? What is what on the trimmer?Fitting blades and trimmer heads AssemblyFitting the J-handle Fitting other guards and cutting attachments Fuel Handling FuelGasoline Two-stroke oilFuelling Starting and stopping Starting and StoppingCheck before starting Stopping Maintenance CarburettorFine adjustment of the idle speed T Correctly adjusted carburettorMuffler High speed jet HCleaning the air filter Cooling systemSpark plug Air filterMaintenance schedule Daily maintenanceWeekly maintenance Monthly maintenanceTechnical Data Technical dataFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsSuper Auto Super Auto II Page Trimmy H Click Trimmy Hit Pro S35 25 m T35 Page ´z+H¶5¨ Page 1140270-95

323RJ, 325RJX-Series specifications

The Husqvarna 323RJ and 325RJX-Series are premier tools in the realm of multi-purpose trimming and landscaping equipment, crafted for both the professional landscaping user and the passionate homeowner. Renowned for their ergonomic design and advanced technology, these models stand out for their performance, efficiency, and innovation.

One of the key features of the Husqvarna 323RJ and 325RJX is their lightweight construction. Weighing significantly less than traditional trimmers, these tools provide users with the ability to work for extended periods without experiencing fatigue. This is especially beneficial for professionals who manage large landscapes and need to maintain productivity throughout the day.

Equipped with Husqvarna's powerful motors, the 323RJ and 325RJX deliver impressive power-to-weight ratios, allowing them to handle even the toughest jobs with ease. The 325RJX, in particular, is designed with a robust engine that ensures high efficiency while minimizing emissions, making it an environmentally conscious option. This aligns with the increasing demand for sustainable landscaping equipment.

The design of these models features an adjustable shaft, enabling users to customize their reach and comfort while eliminating strain on the user's arms and back. The unique angled head allows for easy trimming around obstacles, ensuring that even the most challenging areas can be maintained with precision.

In terms of technology, the Husqvarna 323RJ and 325RJX incorporate Smart Start and fuel pump features that make starting the engine incredibly easy. Users benefit from reduced resistance in the starter cord, translating to fewer pulls to get the equipment running smoothly. This is a significant advantage, particularly when long periods of inactivity might occur during a project.

Additionally, both models are equipped with dual-line tap-and-go cutting systems, promoting efficient weed trimming and allowing users to quickly release more line as needed, enhancing productivity. The ergonomic handles provide a comfortable grip, and features such as the anti-vibration system minimize fatigue, a critical aspect for prolonged use.

Overall, the Husqvarna 323RJ and 325RJX-Series represent the forefront of trimming technology. With their blend of lightweight design, powerful performance, comfort features, and eco-friendly operation, these tools are essential for any serious landscaper looking to achieve remarkable results with efficiency and ease.
Top Page Image Contents