Image IMSG73920, IMSB73920 user manual Using the Hydrotherapy Spa, Wiring the Hydrotherapy SPA

Page 10

Using the Hydrotherapy Spa

The hydrotherapy spa is designed to seat seven adults. The spa holds approximately 375 gallons of water and offers a heating system (80°F to 104°F), a filtration system, and adjustable hydrotherapy jets. Follow the guidelines below to use and maintain the spa for your long-term enjoyment.

WIRING THE HYDROTHERAPY SPA

The hydrotherapy spa is designed to operate with a 240 volt AC power source. It must be wired directly into a grounded circuit with a Ground Fault Circuit Interrupter (GFCI) capable of carrying 50 or more amps. No other appliance should be on the same cir- cuit. Connection of the spa to the 240 volt power source must be performed by a qualified, licensed electrician and must comply with all local, state, and federal electrical codes. Please refer to the instructions on the inside of the electronics package for information about connecting the spa to a 240 volt power source.

Once the spa is filled with water, the power can be turned on. Note: The first time the power is turned on, the spa will start automatically.

TESTING AND TREATING THE WATER

The first time you use the spa, you should test and treat the water. You must also treat the water each time you refill the spa. A test strip and a chemical pack are available at your local pool and spa store. Follow the directions carefully on the chemical pack to test and treat the water. Always keep the chemicals away from children and pets.

See WATER CHEMISTRY on page 13 for information concerning proper water maintenance.

STARTING THE HYDROTHERAPY SPA

You should always test the GFCI before using the hydrotherapy spa. First, turn on the spa by pressing the jet button on the console (see USING THE CON- TROLS on page 12). Once the spa is running, press the GFCI “test” button. The spa should shut off. Press the “reset” button. The spa should resume normal operation. If the spa continues to run after the “test” button is pressed, the GFCI is damaged. Do not use the spa until the GFCI has been repaired or replaced by a qualified electrician.

Once you have tested the GFCI, you should verify the water flow from the pumping unit. Set the air control on the console to the lowest setting (see USING THE CONTROLS on page 12). The pumping unit will heat the water as it pumps. Cover the hydrotherapy spa with the spa cover. The spa cover must be tight (see SECURING THE SPA COVER ON THE SPA on this page). The water will heat at about 6°F per hour with the cover on. If you are using the spa indoors, and the room temperature is maintained at 70°F, it will take approximately 6 to 8 hours for the water to reach the set temperature.

The temperature and the water flow can be set or changed with the controls on the console (see USING THE CONTROLS on page 12).

SECURING THE SPA COVER ON THE SPA

To secure the spa cover,

 

snap the latches on the

 

spa cover into the buckles

Latch

on the panels. To lock the

 

buckles, insert the key and

 

turn it clockwise 1/4 turn.

Key

To unlock the buckles,

insert the key and turn it

 

counterclockwise 1/4 turn.

 

Always keep the buckles

Buckle

locked when the spa is

 

not in use. Keep the

 

keys in a safe place, out of the reach of children.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model No. IMSB73920 IMSG73920 Serial No Customer HOT LineTable of Contents Posting the Warning SignImportant Safety Instructions Read and Follow ALL InstructionsPage Page Before You Begin If you set up the hydrotherapy spa outside If you set up the hydrotherapy spa insideChoosing a Location for the Hydrotherapy Spa Assembly Not shown. Do not overfill the spa Testing and Treating the Water Using the Hydrotherapy SpaWiring the Hydrotherapy SPA Starting the Hydrotherapy SPASpa Shell Diagram Using the Controls Maintenance Sanitizing the Hydrotherapy SPA Attaching and Removing the Access PanelMaintaining the Proper PH Balance Changing the Filter CycleDraining the Pumps Replacing the Light BulbTroubleshooting Symptom the Water Level Drops Part List-Model No. IMSB73920/IMSG73920 R0602A Key No. Qty DescriptionExploded Drawing-Model No. IMSB73920/IMSG73920 R0602A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT

IMSB73920, IMSG73920 specifications

The Image IMSG73920 and IMSB73920 are advanced imaging technologies that offer a plethora of features and capabilities, making them essential tools in various fields such as medical imaging, industrial inspection, and scientific research. These images are capturing significant attention due to their exceptional qualities and cutting-edge technologies.

One of the standout features of the IMSG73920 and IMSB73920 is their remarkable resolution. Equipped with high pixel density, these images provide incredibly detailed visuals, allowing for precise analysis and interpretation. This feature is particularly beneficial in applications like medical diagnostics, where clarity can significantly influence outcomes. The images can reveal minute structures and subtle changes that are crucial for accurate assessments.

In addition to high resolution, these imaging technologies employ advanced sensor technology. The sensors are designed to optimize light capture, improving the quality of images in varied lighting conditions. This capability enables users to capture clear images even in low-light environments, which is essential for applications such as nighttime surveillance or inspections in confined spaces.

Another key characteristic is the incorporation of sophisticated image processing algorithms. These algorithms enhance image clarity and reduce noise, ensuring that the captured visuals are both sharp and realistic. This post-processing feature is particularly useful in scientific research, where accurate data representation is critical for analysis.

Furthermore, the IMSG73920 and IMSB73920 leverage state-of-the-art connectivity options for seamless data transfer. They often come equipped with various communication interfaces, including USB, Ethernet, and wireless options, enabling easy integration with other systems and devices. This functionality supports real-time data sharing and enhances workflow efficiency.

Durability is yet another highlight of these imaging systems. Built with robust materials and designed to withstand harsh environmental conditions, they are ideal for industrial applications where equipment is often exposed to extreme temperatures, moisture, and dust. Their reliability ensures long-term use, reducing the need for frequent replacements or repairs.

Additionally, user-friendly interfaces and customizable settings make these imaging technologies accessible to a broad range of users. This versatility allows professionals from different backgrounds to harness the power of high-quality imaging without requiring extensive technical training.

In summary, the Image IMSG73920 and IMSB73920 stand out due to their high resolution, advanced sensor technology, sophisticated image processing, versatile connectivity, durability, and user-friendly design. These features make them indispensable in various sectors, enhancing the capabilities of professionals who rely on high-quality imaging for their work.
Top Page Image Contents