Image 831.10815 user manual Line. Do not overfill the spa

Page 9

5. Attach the nozzle on the air pump to the valve on

the floor of the Inflatable Liner (29). Use the air pump to fill the bottom of the Inflatable Liner with air.

Be extremely careful not to puncture the Liner. You will need to operate the pump by hand for this step.

Next, attach the nozzle on the air pump to the valve

on the bolster of the Inflatable Liner (29). Fill the bol- ster until there are no wrinkles.

6.Before filling the spa with water, make sure that the spa is in the desired location, that it can easily be serviced, and that the cover can easily be removed.

Once the spa is filled, it will have to be drained before it can be moved.

Using a garden hose or other clean water source, fill the spa until there are 2 to 3 inches of water in the spa. Next, smooth out the wrinkles in the sides

and bottom of the Inflatable Liner (29). Although a few wrinkles are normal, it is very important to smooth out as many wrinkles as possible.

Resume filling the spa until the water reaches the fill

line. Do not overfill the spa.

Note: When the spa is

filled, the Spa

Surround (9) may bow

slightly; this is a

normal condition.

 

 

After the spa is filled, the spa jet unit must be primed before the spa is used (see PRIMING THE

SPA JET UNIT on page 10). Important: Prime the spa jet unit before continuing to step 7.

7.Use the air pump to fill both chambers of the Inflatable Cover (4) with air.

Slide one of the four straps inside the Spa Cover

(11)through one of the loops on the Inflatable Cover

(4).Attach the latch on the strap to the buckle on the other end of the strap. Attach the other three straps

to the loops on the Inflatable Cover in the same way.

8.Place the Spa Cover (11) over the spa and line up the bulge on the Spa Cover with the console on the

dry side jet pack. Snap each of the six latches on the Spa Cover into the buckles on the Spa Surround (9).

9

5

29

 

Air Valve

 

 

 

 

 

Air Valve

6

 

29

Fill Line

 

 

 

 

 

 

9

 

 

7

 

 

Air Valve

 

 

 

 

4

 

 

 

 

 

Pouch for

 

11

 

Jet Plugs

 

 

 

 

 

 

Latches

 

 

 

and Buckles

8

 

 

Bulge

 

 

 

Console

 

 

 

11

 

 

 

Latch

9

 

 

Buckle

 

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Customer HOT Line Model No Serial NoExcluding holidays Sears CANADA, INC., TORONTO, Ontario M5B 2B8Table of Contents Important Safety Instructions Keep all chemicals away from children and petsSee Priming the SPA JET Unit on Has been repaired or replaced by a qualified electrician Using the spaNever use the spa alone Keep pets away from the spa at all timesBefore You Begin If you set up the spa outside If you set up the spa insideChoosing a Location for the Hydrotherapy Spa An extension cord cannot be used with the spaAssembly CrossSection Drawing 4A Pushed fully through the vinyl linerLine. Do not overfill the spa Testing and Treating the Water Using the Hydrotherapy SpaPriming the SPA JET Unit Plugging in the SPASPA JET Unit Operation Heating System of Your SPASecuring the SPA Cover ImporDraining the Pump Using the ConsoleDraining the SPA TurnMaintenance Symptom the SPA will not Operate Trouble-shootingSymptom the Pump Hums Symptom the Water Pulsates or There is Minimum Water FlowSymptom the Water Level Drops Symptom the Water is not Being Cleaned by the FilterSymptom the SPA Pump Loses ITS Prime Be kept outdoors in cold weather, you mustPage Page Model No Customer RecordLimited 90 Day Spa Warranty Model Number of the product Name of the product Image Ordering Replacement PartsIs a registered trademark of Icon Health & Fitness, Inc Part No R1199ACustomer Service Cleaning and Maintaining the SpaChoosing a Location for the Spa Plugging in the SpaLit Pack Qty Qty831.108150
Top Page Image Contents