Image IMHS45590 manual

Page 9

3.Refer to the inset drawing. Set a Filter Gasket (33) on top of the Filter (16). Next, press the Filter Cover

(8) into the spa until it is fully seated. Then, tighten the Locking Ring (19) onto the spa.

Remove the two warning decals (not shown) from the spa shell. Using a damp cloth, wipe the spa shell clean. Before filling the spa, make sure that it is in the desired position and that there is room to easily service the spa. Once the spa is filled, it will have to be drained before it can be moved.

Turn the Air Vent (29) counterclockwise to open it. Using a garden hose or other clean water source, begin filling spa. Do not use soft water. The spa may be filled with cold water; however, if warm or hot water is used, the spa will be ready for use sooner. Fill the spa until the water is at the level shown at the right. Do not overfill the spa.

Turn the Air Vent (29) clockwise to close it.

4.Attach the nozzle of the included air pump to the valves on the Inflatable Cover (4). Fill the Inflatable Cover with air. Do not overfill the Inflatable Cover.

Slide one of the straps on the inside of the Spa Cover (11) through one of the loops on the Inflatable Cover (4). Attach the latch on the strap to the buckle on the other end of the strap. Make sure that the cutout in the Inflatable Cover is lined up with the warning label on the Spa Cover. Attach the other three straps on the inside of the Spa Cover through the loops on the Inflatable Cover in the same way. Place the Spa Cover over the spa and line up the cutout in the Inflatable Cover with the Console (not shown).

5.Pull down one of the straps on the Spa Cover (11) and hold the Buckle (30) against one of the wood panels on the spa. (Note: To position the Buckle cor- rectly, have a second person hold the strap on the opposite side of the Spa Cover tight.) The Spa

Cover must be tight. Do not place the Buckle over the grooves between the wood panels. Refer to the inset drawing. Remove the latch from the Buckle (30). Attach the Buckle to the wood panel with two #4 x 3/4Ó Screws (31). Note: It may be helpful to use a drill with a 1/16Ó bit to make starter holes in the wood panel. It may also be helpful to apply a little soap or wax to the screw threads.

Attach the other five Buckles (30) to the wood panels in the same way.

Remove the Spa Cover (11) and the Inflatable Cover (not shown) from the spa.

3

19

 

8

33

Fill to Here

 

16

 

 

 

 

 

 

 

 

 

 

 

 

29

4

4

 

 

Loop

 

Cutout

 

Buckle

Strap

 

Latch

 

11

 

Warning

 

Label

5

11

 

 

Strap

 

Latch

 

30

 

31

 

Strap

 

30

9

Image 9
Contents Customer HOT Line Model No. IMHS45590 Serial NoPosting the Warning Sign Table of ContentsRead and Follow ALL Instructions Important Safety InstructionsPage Page Before You Begin If you set up the hydrotherapy spa outside If you set up the hydrotherapy spa insideChoosing a Location for the Hydrotherapy Spa Do not use an extension cord with the hydrotherapy spaAssembly Page Testing and Treating the Water Using the Hydrotherapy SpaPlugging in the Hydrotherapy SPA Starting the Hydrotherapy SPASecuring the SPA Cover on the SPA Spa Shell DiagramUsing the Controls Maintenance Water Chemistry Attaching and Removing the Access PanelMaintaining the Proper PH Balance Draining the Hydrotherapy SPAReplacing the Light Bulb Draining the PumpTrouble-shooting Symptom the Console Displays the Words Òcooló or Òiceó Symptom the Console Displays ONEÒilocó Key No. Qty Description Part ListÑModel No. IMHS45590Exploded DrawingÑModel No. IMHS45590 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT