Univex 2348LS, 96043004400 owner manual Mowing Tips, Purge Transmission

Page 13

OPERATION

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is running.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the en- gine is running, move throttle control to slow position. Disengage parking brake.

CAUTION: At any time there may be movement of the drive wheels.

•Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five

(5) seconds and release pedal. Repeat this procedure three (3) times.

•Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

•Drive tractor forward for approximately five feet then backwards for five feet. Repeat this driving procedure three times.

Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 12).

FIG. 11

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 2348LS Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To SET Parking BRAKESee a HOW to USE Your TractorStopping See b To USE Throttle Control D SeeTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Move Forward and Backward See FigTo Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsBefore Starting the Engine Service REMINDER/HOUR MeterCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsLubrication Chart MaintenanceBrake Operation TractorTires Blade CareEngine Cleaning To Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig First Install ANTI-SWAY BAR S Engage belt tension rod K on locking bracket L To Level Mower To Replace Mower Blade Drive Belt Mower Drive Belt InstallationMower Drive Belt Removal To Replace Motion Drive Belt See Fig Belt InstallationBelt Removal To Check Brake To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when SCH12 SchematicElectrical KEY Part Description Chassis Chassis Drive Nut U-CHNL 1/4-20 550DP .350 PNL Engine Spark Arrester KITEngine Power Rating Information Steering Assembly 532 41 Wheel, Steering 532 19 532 40 Seat Seat AssemblyWheels and Tires DecalsMower Deck 532 41 87-00 Deck Weldment Mower Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationService Notes Service Notes 532 41 84-82 Rev 09.11.08 SBW

2348LS, 96043004400 specifications

The Univex 96043004400,2348LS is an advanced piece of equipment designed to meet the demands of modern food processing and preparation. This versatile machine is recognized in the industry for its reliability and efficiency, making it an essential tool for restaurants, catering businesses, and food manufacturing facilities.

One of the standout features of the Univex 96043004400,2348LS is its powerful motor. With robust horsepower, it provides exceptional mixing capabilities, allowing for the preparation of large batches of ingredients with ease. This power is complemented by a range of speed settings, delivering customizable performance to suit various mixing requirements, whether it’s dough, batters, or other food preparations.

The design of the Univex 96043004400,2348LS highlights both functionality and user-friendliness. The machine is equipped with a large capacity bowl, enabling users to handle significant quantities of ingredients efficiently. The stainless steel construction of the bowl and other components not only ensures durability but also makes cleaning and maintenance straightforward, which is crucial for maintaining hygiene standards in food preparation environments.

One of the key technologies integrated into the Univex 96043004400,2348LS is its planetary mixing system. This technology ensures that every ingredient is evenly mixed, eliminating the risk of unmixed portions, resulting in consistent quality across batches. The machine also offers various attachments, such as whisk and dough hooks, enhancing its versatility for different types of tasks.

Safety features are an important consideration in the design of the Univex 96043004400,2348LS. The machine comes equipped with a safety guard that prevents access to the mixing area while the machine is in operation, minimizing the risk of accidents. Additionally, the machine's sturdy base and design ensure stability during use, further enhancing safety.

In conclusion, the Univex 96043004400,2348LS is a robust and versatile mixing machine that stands out for its powerful motor, durable design, and advanced mixing technology. Its wide range of speed settings and attachments makes it suitable for various culinary tasks, while its safety features ensure a secure working environment. This machine is an investment in efficiency and quality for any food processing operation.
Top Page Image Contents