Univex 2348LS, 96043004400 To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 25

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig 30)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent spark- ing from accidental grounding.

1.Lift hood to raised position.

2.Disconnect BLACK battery cable (A) then RED battery cable and carefully remove battery from tractor.

3.Install new battery with terminals in same position as old battery.

4.First connect RED battery cable (B) to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover (C) over terminal.

5.Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

6.Close hood.

A NEGATIVE(BLACK)

CABLE

C

POSITIVE B (RED)

CABLE

02954

FIG. 30

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02778

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 2348LS Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To SET Parking BRAKESee a HOW to USE Your TractorStopping See b To USE Throttle Control D SeeTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Move Forward and Backward See FigTo Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsBefore Starting the Engine Service REMINDER/HOUR MeterCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsLubrication Chart MaintenanceBrake Operation TractorTires Blade CareEngine Cleaning To Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig First Install ANTI-SWAY BAR S Engage belt tension rod K on locking bracket L To Level Mower To Replace Mower Blade Drive Belt Mower Drive Belt InstallationMower Drive Belt Removal To Replace Motion Drive Belt See Fig Belt InstallationBelt Removal To Check Brake To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when SCH12 SchematicElectrical KEY Part Description Chassis Chassis Drive Nut U-CHNL 1/4-20 550DP .350 PNL Engine Spark Arrester KITEngine Power Rating Information Steering Assembly 532 41 Wheel, Steering 532 19 532 40 Seat Seat AssemblyWheels and Tires DecalsMower Deck 532 41 87-00 Deck Weldment Mower Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationService Notes Service Notes 532 41 84-82 Rev 09.11.08 SBW

2348LS, 96043004400 specifications

The Univex 96043004400,2348LS is an advanced piece of equipment designed to meet the demands of modern food processing and preparation. This versatile machine is recognized in the industry for its reliability and efficiency, making it an essential tool for restaurants, catering businesses, and food manufacturing facilities.

One of the standout features of the Univex 96043004400,2348LS is its powerful motor. With robust horsepower, it provides exceptional mixing capabilities, allowing for the preparation of large batches of ingredients with ease. This power is complemented by a range of speed settings, delivering customizable performance to suit various mixing requirements, whether it’s dough, batters, or other food preparations.

The design of the Univex 96043004400,2348LS highlights both functionality and user-friendliness. The machine is equipped with a large capacity bowl, enabling users to handle significant quantities of ingredients efficiently. The stainless steel construction of the bowl and other components not only ensures durability but also makes cleaning and maintenance straightforward, which is crucial for maintaining hygiene standards in food preparation environments.

One of the key technologies integrated into the Univex 96043004400,2348LS is its planetary mixing system. This technology ensures that every ingredient is evenly mixed, eliminating the risk of unmixed portions, resulting in consistent quality across batches. The machine also offers various attachments, such as whisk and dough hooks, enhancing its versatility for different types of tasks.

Safety features are an important consideration in the design of the Univex 96043004400,2348LS. The machine comes equipped with a safety guard that prevents access to the mixing area while the machine is in operation, minimizing the risk of accidents. Additionally, the machine's sturdy base and design ensure stability during use, further enhancing safety.

In conclusion, the Univex 96043004400,2348LS is a robust and versatile mixing machine that stands out for its powerful motor, durable design, and advanced mixing technology. Its wide range of speed settings and attachments makes it suitable for various culinary tasks, while its safety features ensure a secure working environment. This machine is an investment in efficiency and quality for any food processing operation.
Top Page Image Contents