Ryobi Outdoor RY52002 manual Chain Oiler, Fueling and Refueling, Premium Exact MIX

Page 10

ASSEMBLY

To remove:

nLoosen the knob.

nPush in the button and twist the shafts to remove and separate ends.

nCarefully pour fuel into the tank. Avoid spillage.

nPrior to replacing the fuel cap, clean and inspect the gasket.

nImmediately replace fuel cap and hand tighten. Wipe up any fuel spillage.

GUIDE

POWER HEAD

SHAFT

COUPLER

NOTE: It is normal for smoke to be emitted from a new engine after first use.

RECESS

BUTTON

POSITIONING

KNOB

HOLE

PRUNER

 

ATTACHMENT

Fig. 4

CHAIN OILER

Add bar and chain oil in the chain oiler tank before starting the engine of the power head.

FUELING AND REFUELING

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires pre- mixing gasoline and 2-cycle oil. Pre-mix unleaded gasoline and 2-cycle engine oil in a clean 1 gallon container approved for gasoline.

nThis engine is certified to operate on unleaded gasoline intended for automotive use.

nMix high quality 2-cycle engine oil at 2.6 oz. per gallon.

nDo not use automotive oil or 2-cycle outboard oil.

nDO NOT mix quantities larger than usable in a 30-day period.

PREMIUM EXACT MIX™ (50:1)

GASOLINE

OIL

1 Gallon (US)

2.6 oz.

1 Liter

20 cc (20 ml)

FILLING TANK

n Clean surface around fuel cap to prevent contami- nation.

n Loosen fuel cap slowly. Rest the cap on a clean surface.

WARNING:

Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting the engine. Do not smoke!

INSTALLING THE GRASS DEFLECTOR ON THE STRING TRIMMER ATTACHMENT

See Figure 5.

WARNING:

The line cutting blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury.

nPress the grass deflector onto the bottom of the curved shaft as shown.

nInsert the hex screw through the grass deflector and the bracket on the curved shaft.

nPlace the flat washer and lock washer on the hex head cap screw.

nPlace the wing nut on the hex head cap screw and tighten securely.

HEX

SCREWGRASS DEFLECTOR

BRACKET

 

LOCK

 

WASHER

FLAT

 

WASHER

WING NUT

 

Fig. 5

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules for Trimmer USE Specific Safety RulesSpecific Safety Rules for Pruner USE RefuelingSymbols Symbol Name DESIGNATION/EXPLANATIONService Throttle Trigger Product SpecificationsStarter Grip Chain Oiler Tank CAP Engine Switch Coupler KnobFeatures AssemblyAttaching the J Barrier Handle Installing the Shoulder StrapConnecting the Power Head to Pruner AttachmentFueling and Refueling Chain OilerPremium Exact MIX Preparation for Pruner Cutting OperationSee Figures 6 See Figures 8 Limbing and PruningOperating the Trimmer MaximumCutting Tips To Advance the Cutting LineTo Advance the Cutting Line Manually Grass Deflector Line Trimming CUT-OFF BladeStarting and Stopping Position for StartingSee Figures 14 Chain Tension MaintenanceGeneral Maintenance See Figures 17Chain BAR BAR NUT Replacing the BARSee Figures 19 BAR NUT Chain Tensioning ScrewIdle Speed Screw Idle Speed AdjustmentChain Oiler Tank Replace CAP Remove HOW to Sharpen the Cutters Chain MaintenanceSee Figures 28 See Figures 32 Spool ReplacementNEW Prewound Spool Spool Retainer Spring Slots Eyelets String Head ShaftArrows on Spool Anchor Hole String ReplacementSee Figures 34 First String SlotSpark Arrestor Cleaning the Exhaust Port and MufflerReplacing and Cleaning AIR Filter Fuel CAPTroubleshooting Problem Cause RemedyWarranty Limited Warranty StatementMaintenance Requirements MANUFACTURER’S Warranty CoverageOWNER’S Warranty Responsibilities CoverageThis Product WAS Manufactured with a Catalyst Muffler Service Model NO. and Serial no California Proposition
Top Page Image Contents