Ryobi 197788 manual Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 13

OPERATION

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

Transmission Engaged

Transmission Disengaged

FIG. 8

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Pull up and remove oil fill cap/dipstick; wipe oil off. Re- insert the dipstick into the tube and push down firmly into place. Remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

13

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 4)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place motion control lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to“START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Always Wear EYE Protection During Operation HDK19H42Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

197788 specifications

The Ryobi 197788 is a versatile and innovative tool that caters to the needs of both DIY enthusiasts and professional contractors. This battery-operated, compact tool is designed to deliver outstanding performance in a variety of applications, making it a go-to choice for anyone looking to complete tasks efficiently and effectively.

One of the standout features of the Ryobi 197788 is its brushless motor technology. This advanced motor not only increases the tool's efficiency but also enhances its longevity. Brushless motors are known for producing less heat and requiring less maintenance, which translates to greater reliability during use. The powerful motor ensures that users can tackle even the most demanding projects without compromising performance.

The Ryobi 197788 is equipped with a variable speed trigger, allowing users to adjust the speed according to the specific requirements of the task at hand. This feature provides enhanced control whether drilling, driving, or screwing. Additionally, the tool boasts an ergonomic design, featuring a comfortable grip that reduces fatigue during extended use. This important characteristic makes the Ryobi 197788 an excellent choice for those tackling large jobs or working in tight spaces.

Another remarkable aspect of the Ryobi 197788 is its compatibility with the Ryobi ONE+ battery system. This system allows users to interchange batteries across a wide range of tools, which saves time and money. The included battery is designed for maximum runtime, providing ample power to keep you going without frequent interruptions.

The Ryobi 197788 is also equipped with built-in LED lighting, ensuring that users can work in low-light conditions without sacrificing visibility. The integrated lights illuminate the work area, allowing for precise work even in dimly lit environments. This feature is particularly useful for those who often find themselves working in garages, attics, or sheds.

Additionally, the tool’s compact size allows for easy maneuverability and storage. Weighing in at a lightweight design, the Ryobi 197788 can easily be transported to different job sites without causing strain.

In summary, the Ryobi 197788 is a powerful and efficient tool that combines advanced technologies with user-friendly features. Its brushless motor, variable speed trigger, ergonomic design, battery compatibility, and built-in LED lighting make it a reliable option for a diverse range of applications. Whether you are a seasoned professional or a DIY novice, this tool can significantly enhance your productivity and make your projects more enjoyable.
Top Page Image Contents