Ryobi 197788 manual Check Battery See Fig

Page 7

ASSEMBLY

SEAT

SEAT PAN

SHOULDER

BOLTS

02617

FLAT WASHER

02615

ADJUSTMENT

KNOB

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Always Wear EYE Protection During Operation HDK19H42II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

197788 specifications

The Ryobi 197788 is a versatile and innovative tool that caters to the needs of both DIY enthusiasts and professional contractors. This battery-operated, compact tool is designed to deliver outstanding performance in a variety of applications, making it a go-to choice for anyone looking to complete tasks efficiently and effectively.

One of the standout features of the Ryobi 197788 is its brushless motor technology. This advanced motor not only increases the tool's efficiency but also enhances its longevity. Brushless motors are known for producing less heat and requiring less maintenance, which translates to greater reliability during use. The powerful motor ensures that users can tackle even the most demanding projects without compromising performance.

The Ryobi 197788 is equipped with a variable speed trigger, allowing users to adjust the speed according to the specific requirements of the task at hand. This feature provides enhanced control whether drilling, driving, or screwing. Additionally, the tool boasts an ergonomic design, featuring a comfortable grip that reduces fatigue during extended use. This important characteristic makes the Ryobi 197788 an excellent choice for those tackling large jobs or working in tight spaces.

Another remarkable aspect of the Ryobi 197788 is its compatibility with the Ryobi ONE+ battery system. This system allows users to interchange batteries across a wide range of tools, which saves time and money. The included battery is designed for maximum runtime, providing ample power to keep you going without frequent interruptions.

The Ryobi 197788 is also equipped with built-in LED lighting, ensuring that users can work in low-light conditions without sacrificing visibility. The integrated lights illuminate the work area, allowing for precise work even in dimly lit environments. This feature is particularly useful for those who often find themselves working in garages, attics, or sheds.

Additionally, the tool’s compact size allows for easy maneuverability and storage. Weighing in at a lightweight design, the Ryobi 197788 can easily be transported to different job sites without causing strain.

In summary, the Ryobi 197788 is a powerful and efficient tool that combines advanced technologies with user-friendly features. Its brushless motor, variable speed trigger, ergonomic design, battery compatibility, and built-in LED lighting make it a reliable option for a diverse range of applications. Whether you are a seasoned professional or a DIY novice, this tool can significantly enhance your productivity and make your projects more enjoyable.
Top Page Image Contents