Ryobi 197788 manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP

Page 14

OPERATION

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

•Allow one minute for transmission to warm up.This can be done during the engine warm up period.

•The attachments can also be used during the engine warm-up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly dis- engage clutch/brake pedal.

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the mo- tion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 9).

FIG. 9

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents HDK19H42 Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigAutomatic Transmission Warm UP Mowing TipsPurge Transmission General Recommendations MaintenanceLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

197788 specifications

The Ryobi 197788 is a versatile and innovative tool that caters to the needs of both DIY enthusiasts and professional contractors. This battery-operated, compact tool is designed to deliver outstanding performance in a variety of applications, making it a go-to choice for anyone looking to complete tasks efficiently and effectively.

One of the standout features of the Ryobi 197788 is its brushless motor technology. This advanced motor not only increases the tool's efficiency but also enhances its longevity. Brushless motors are known for producing less heat and requiring less maintenance, which translates to greater reliability during use. The powerful motor ensures that users can tackle even the most demanding projects without compromising performance.

The Ryobi 197788 is equipped with a variable speed trigger, allowing users to adjust the speed according to the specific requirements of the task at hand. This feature provides enhanced control whether drilling, driving, or screwing. Additionally, the tool boasts an ergonomic design, featuring a comfortable grip that reduces fatigue during extended use. This important characteristic makes the Ryobi 197788 an excellent choice for those tackling large jobs or working in tight spaces.

Another remarkable aspect of the Ryobi 197788 is its compatibility with the Ryobi ONE+ battery system. This system allows users to interchange batteries across a wide range of tools, which saves time and money. The included battery is designed for maximum runtime, providing ample power to keep you going without frequent interruptions.

The Ryobi 197788 is also equipped with built-in LED lighting, ensuring that users can work in low-light conditions without sacrificing visibility. The integrated lights illuminate the work area, allowing for precise work even in dimly lit environments. This feature is particularly useful for those who often find themselves working in garages, attics, or sheds.

Additionally, the tool’s compact size allows for easy maneuverability and storage. Weighing in at a lightweight design, the Ryobi 197788 can easily be transported to different job sites without causing strain.

In summary, the Ryobi 197788 is a powerful and efficient tool that combines advanced technologies with user-friendly features. Its brushless motor, variable speed trigger, ergonomic design, battery compatibility, and built-in LED lighting make it a reliable option for a diverse range of applications. Whether you are a seasoned professional or a DIY novice, this tool can significantly enhance your productivity and make your projects more enjoyable.
Top Page Image Contents