Ryobi 197788 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Figs. 26 and 27)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 26

TERMINAL

KEPS

NUT

COVER

 

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 27

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

01536

FIG. 28

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Always Wear EYE Protection During Operation HDK19H42II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Before Each USE MaintenanceLubrication Chart General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

197788 specifications

The Ryobi 197788 is a versatile and innovative tool that caters to the needs of both DIY enthusiasts and professional contractors. This battery-operated, compact tool is designed to deliver outstanding performance in a variety of applications, making it a go-to choice for anyone looking to complete tasks efficiently and effectively.

One of the standout features of the Ryobi 197788 is its brushless motor technology. This advanced motor not only increases the tool's efficiency but also enhances its longevity. Brushless motors are known for producing less heat and requiring less maintenance, which translates to greater reliability during use. The powerful motor ensures that users can tackle even the most demanding projects without compromising performance.

The Ryobi 197788 is equipped with a variable speed trigger, allowing users to adjust the speed according to the specific requirements of the task at hand. This feature provides enhanced control whether drilling, driving, or screwing. Additionally, the tool boasts an ergonomic design, featuring a comfortable grip that reduces fatigue during extended use. This important characteristic makes the Ryobi 197788 an excellent choice for those tackling large jobs or working in tight spaces.

Another remarkable aspect of the Ryobi 197788 is its compatibility with the Ryobi ONE+ battery system. This system allows users to interchange batteries across a wide range of tools, which saves time and money. The included battery is designed for maximum runtime, providing ample power to keep you going without frequent interruptions.

The Ryobi 197788 is also equipped with built-in LED lighting, ensuring that users can work in low-light conditions without sacrificing visibility. The integrated lights illuminate the work area, allowing for precise work even in dimly lit environments. This feature is particularly useful for those who often find themselves working in garages, attics, or sheds.

Additionally, the tool’s compact size allows for easy maneuverability and storage. Weighing in at a lightweight design, the Ryobi 197788 can easily be transported to different job sites without causing strain.

In summary, the Ryobi 197788 is a powerful and efficient tool that combines advanced technologies with user-friendly features. Its brushless motor, variable speed trigger, ergonomic design, battery compatibility, and built-in LED lighting make it a reliable option for a diverse range of applications. Whether you are a seasoned professional or a DIY novice, this tool can significantly enhance your productivity and make your projects more enjoyable.
Top Page Image Contents