Patriot Products 1900 Inspect Muffler and Spark Arresting Screen, Carburetor Adjustments

Page 14

harmful emissions. Always clean after every 5 hours of operation.

SClean the cover and the area around it to keep dirt and sawdust from falling into the carburetor chamber when the cover is re- moved.

SRemove the parts as illustrated below.

SWash the filter in soap and water. Air dry completely before reinstalling.

SLightly oil air filter before installing to im- prove the efficiency of the air filter. Use

2--cycle engine oil or motor oil (SAE 30). Squeeze excess oil from filter.

SReinstall parts.

 

 

 

Air Filter

Cylinder Cover

Screws

 

 

 

 

Cylinder

 

Cover

 

INSPECT MUFFLER AND SPARK ARRESTING SCREEN

As the unit is used, carbon deposits build up on the muffler and spark arresting screen, and must be removed to avoid creating a fire hazard or affecting engine performance.

Replace the spark arresting screen if breaks occur.

Muffler Diffuser

Spark Arresting Screen

Muffler

Cover

Screws

Muffler Muffler

BodyCover

CLEANING THE SPARK ARREST- ING SCREEN

Cleaning is required every 25 hours of op- eration or annually, whichever comes first. S Loosen and remove the 2 muffler cover

screws.

SRemove the muffler cover (cover snaps off

muffler body).

SRemove muffler diffuser and spark arrest-

ing screen assembly. Notice the orienta- tion of these parts for reassembling.

SClean the spark arresting screen with a wire

brush. Replace screen if breaks are found. S Replace any broken or cracked muffler

parts.

SReinstall diffuser and spark arresting screen

assembly with round holes facing up.

S Reinstall muffler cover and 2 screws. Tighten securely.

CARBURETOR ADJUSTMENTS

Your carburetor is equipped with limiter caps. Carburetor adjustment is a compli- cated task. We recommend that you take your unit to an Authorized Service Dealer. Damage will occur if you turn the needles be- yond the limiter stops.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be neces- sary to service your bar. A worn bar will dam- age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi-

tion.

SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from

saw.

S Clean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Sprocket Hole

Oil Holes

SAdd lubricant to sprocket hole after each use.

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when excess heating or burring of the rails occurs. If replacement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better.

SLoosen 3 screws on cylinder cover. S Remove the cylinder cover.

S Pull off the spark plug boot.

S Remove spark plug from cylinder and dis- card.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Starting or operating the chain sawHandle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackMaintain Control Kickback Safety FeaturesReduce the Chance Kickback Avoid Obstructions Clear The Working AreaSume That the Chain Brake will Chain Brake and CKA AngleResent and YOU should not AS Protect YOU in the Event of aInside view Chain Brake Adjustment located on Chain Brake Attaching the BAR & Chain If notChecking the tension Adjusting the tensionChain Tension Fit bottom of drive links between the teethThrottle Trigger ON/STOP SwitchKnow Your Chain SAW Throttle LOCK-OUTImportant Points to Remember Fueling EngineBAR and Chain Lubrication Braking function control Caution The chain brake must be Starting a Warm EngineDifficult Starting or starting a flooded engine Inertia activating function controlFooting Tree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Types of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportLimbing and Pruning Important Points Cleaning the air filterPruning LimbingBAR Maintenance Cleaning the Spark ARREST- ING ScreenCarburetor Adjustments Inspect Muffler and Spark Arresting ScreenTroubleshooting Table Cause Remedy StorageContact your dealer or place of purchase Ligations The U. S. EnvironmentalEater service centers. call 1--800--554--6723MAINTENANCE, RE Weed Eater servicing center. Conse

1900 specifications

Patriot Products 1900 is a compact and efficient wood chipper designed specifically for home landscaping and yard maintenance. Ideal for homeowners with small to medium-sized properties, this unit stands out for its powerful performance and user-friendly features, making it a popular choice among DIY enthusiasts and professional landscapers alike.

One of the main features of the Patriot Products 1900 is its robust engine. Powered by a reliable 14 HP Honda engine, it offers exceptional torque and speed, allowing for the chipping of branches up to 2 inches in diameter with ease. The engine is designed for optimal fuel efficiency and minimal emissions, aligning with environmentally conscious practices.

The chipper’s design incorporates a unique feed system that enhances productivity. It features a large, oversized hopper that allows users to easily feed branches and yard debris into the machine. This design minimizes the risk of clogging, which is a common issue in smaller chippers. The oversized blades are constructed from high-quality steel, ensuring longevity and sharpness for consistent performance.

Another significant characteristic of the Patriot Products 1900 is its portability. With a sturdy steel frame and 10-inch pneumatic wheels, this chipper is easy to maneuver across various terrains. It can be effortlessly transported from one location to another, making it an excellent choice for individuals who need to perform yard work in different areas.

Safety is a top priority in the design of the Patriot Products 1900. It is equipped with several safety features, including a safety shut-off switch and a protective housing, to prevent accidental injuries during operation. Users can operate the chipper with confidence knowing that their safety is safeguarded.

In terms of maintenance, the Patriot Products 1900 is straightforward. It comes with a simple user manual and guidelines for routine checks and upkeep. This ensures that users can keep the machine in top condition without excessive hassle.

Overall, the Patriot Products 1900 boasts a winning combination of power, efficiency, portability, and safety. Whether tackling yard clean-up tasks, preparing mulch for gardens, or managing storm debris, this wood chipper is designed to make the job easier and more efficient for all users. Its advanced features and thoughtful design set it apart as a reliable tool in the realm of landscaping equipment.
Top Page Image Contents