Porter-Cable D27927-034-0 Pressure Washer Terminology, Pressure Washer Operating Features

Page 11
Thermal Relief Valve

PRESSURE WASHER TERMINOLOGY

PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc.

GPM: Gallons Per Minute. The unit of measure for the flow rate of water.

CU: Cleaning Units. GPM multiplied by PSI.

Bypass Mode: In Bypass Mode, the pump is recirculating water because the trigger of the spray gun is not pulled. If unit is left in bypass mode for more than two (2) minutes, the water temperature will rise to a dangerous level and could damage internal components of the pump. Any damage to pump due to these causes will not be covered under warranty.

DO NOT allow your unit to operate in bypass mode for more than two minutes at any time. Overheating of pump can

cause damage to pump.

Thermal Relief Valve: In an effort to prevent extreme damage, pumps are equipped with a thermal relief valve. This valve will open when the temperature inside the pump rises too high. This valve will then release a gush

of water in an effort to lower the temperature inside the pump. Immediately after this occurs, the valve will close.

Chemical Injection System: Mixes cleaners or cleaning solvents

with the pressurized water to improve cleaning effectiveness.

Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 PSI and 5 gallons per minute.

PRESSURE WASHER OPERATING FEATURES

PRESSURE ADJUSTMENTS

The pressure setting is preset at the factory to achieve optimum pressure and cleaning. If you need to lower the pressure, it can be accomplished by these methods.

1.Back away from the surface to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned.

2.Change to the 40º nozzle - white, this nozzle delivers a less powerful stream of water and a wider spray pattern.

DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may damage pump.

3.Adjust the pressure regulator on the pump. Turn the pressure regulator knob counterclockwise to lower pressure. Refer to the illustrations to identify your pressure regulator. Once you have finished using your pressure washer, return the pressure regu- lator to its original position by turning it clockwise.

DO NOT try to turn pressure regulator knob past the built-in stop or damage to pump will result.

Pressure

Regulator

Knob

11- ENG

D27927

Page 10 Page 12
Image 11
Page 10 Page 12
Contents PCK3030SP ManualConsumer Safety Information Safety Guidelines DefinitionsRisk to Breathing Important Safety InstructionsMaintenance Instructions Risk of Explosion or FireRisk of Chemical Burn Risk to Fluid InjectionRisk of HOT Surfaces Risk of Unsafe OperationRisk of Electrical Shock Risk of Injury from Spray Consumer General and Service InformationCarton Contents Assembly Instructions ENG D27927 Reference Operating InstructionsBasic Elements of a Pressure Washer Basic Elements of EnginePressure Washer Terminology Pressure Washer Operating FeaturesPressure Adjustments To USE Spray Wand To Apply chemicals HOW to Apply Chemicals and Cleaning SolventsRead and Understand ALL Warnings Before Starting Unit Depress trigger on gun to start water flow. Note If applying a chemical or cleaning solution, seeStarting Shutting DownTo Check Oil MaintenanceHow To Change Pump Oil Engine PumpHOW to Clean the Water Inlet Filter Nozzle CleaningStorage Causecorrection Trouble Shooting GuideProblem Chemicals Problem Cause CorrectionLimited Warranty

D27927-034-0, PCK3030SP specifications

The Porter-Cable PCK3030SP is a versatile and powerful tool that stands out in the realm of compact toolsets. Designed for both professional and DIY use, this 30-piece kit includes essential accessories, making it an ideal choice for a wide range of applications. One of the main features of the PCK3030SP is its high-quality construction, which ensures durability and longevity, even under demanding work conditions.

The toolset includes a variety of drill bits, chisels, and other accessories that cater to various tasks, from woodworking to metalworking. The drill bits are designed for superior performance and precision, allowing users to achieve clean and accurate results with ease. Furthermore, the PCK3030SP is compatible with standard drill chucks, ensuring seamless integration with different drill models.

Another significant aspect of the Porter-Cable PCK3030SP is its user-friendly design. The tools are lightweight and easy to handle, reducing fatigue during extended use. This design consideration makes the set ideal for both beginners looking to develop their skills and seasoned professionals seeking reliable performance.

In addition to the PCK3030SP, the D27927-034-0 is also an impressive product within the Porter-Cable lineup. This model features advanced technologies that enhance its efficiency and effectiveness. Constructed with a focus on precision, the D27927-034-0 offers precision cutting, making it suitable for a wide range of materials.

Key features of the D27927-034-0 include its robust motor, which delivers substantial power and performance for demanding tasks. Its ergonomic design ensures ease of use, providing operators with better control and reducing overall strain. Additionally, the model is equipped with safety features, such as overload protection and a quick-release locking mechanism, further enhancing its usability and protecting against potential hazards.

In summary, both the Porter-Cable PCK3030SP and the D27927-034-0 exemplify the brand's commitment to providing high-quality, reliable tools that cater to the diverse needs of users. With advanced technologies, durable construction, and user-centric designs, these tools are valuable additions to any workshop, whether for professional tradespeople or enthusiastic home renovators. Their combination of performance and ease of use positions them as standout choices in the tool market.
Top Page Image Contents