Porter-Cable PCH3031A, D26183-025-1 instruction manual Starting, To Shut Down, Cone side faces out

Page 12

TO SHUT DOWN

IMPORTANT: Read and understand how to shut down the pressure washer before operating.

1.If you have siphoned chemicals, siphon a bucket of clean water through the chemical hose. NOTE: Failure to do so will cause damage to the pump.

2.Refer to engine manual for correct engine shut down procedure.

NOTE: NEVER turn the water off with the engine running.

3.Turn water source off.

4.Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

5.See Storage section in this manual for proper storage procedures.

STARTING

Prior to starting, refer to your engine manual for proper starting procedures for your engine type.

1.In a well ventilated outdoor area Add fresh high quality unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine manual for correct procedure.

2.Check engine oil level. See Engine Operators Manual for correct procedure.

NOTE: There will be a slight amount of oil in the engine from factory testing.

3.

Verify the filter screen is in water inlet of pump. NOTE:

Filter Screen

 

Cone side faces out.

 

 

4.

Connect water source to pump inlet.

 

 

NOTE: Water source must provide a minimum of 5

 

 

gallons per minute at 20 p.s.i.

 

5.Connect high pressure hose to pump outlet.

6.If applying a chemical or cleaning solution, see How To Siphon Chemicals/Cleaning Solvents in Operation section of this manual.

7.

Turn water source on. NOTE: Make sure water

High Pressure Hose

 

 

supply is turned on.

 

8.

Start engine. See Engine operators Manual for correct

 

procedure. NOTE: If the engine does not start after two pulls, pull the trigger to relieve the pressure.

9.Depress trigger on gun to start water flow. NOTE:

Stand on a stable surface and grip gun/wand firmly

Water

with both hands. Expect the gun to kick when

Source

 

triggered.

 

 

10.Release trigger to stop water flow.

11.Adjust nozzle spray for the task being performed or change quick connect tip. See How To Use Wand instructions in this section.

D26183

12- ENG

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Instruction General Information Safety Guidelines / Definitions Important Safety InstructionsHazard What can Happen Risk Unsafe Operation BOX Contents Assembly Operation Basic Elements of EnginePressure Washer Throttle Control Lever Controls engine speedHOW to USE To Adjust PressurePressure Washer Terminology To USE Wand To Siphon CHEMICALS/CLEANING Solvents Read and Understand ALL Warnings Before Starting UnitPress chemical hose onto barbed fitting located Starting To Shut DownVerify the filter screen is in water inlet of pump. Note Cone side faces outMaintenance How To Change Pump OilEngine PumpHOW to Clean the Water Inlet Filter WandStorage Engine PumpWindshield washer fluid may also be used Trouble Shooting Guide Problem CausecorrectionProblem CauseCorrection Limited Warranty Responsibility of Original Purchaser initial UserENG D26183 Quick Facts Call

PCH3031A, D26183-025-1 specifications

The Porter-Cable D26183-025-1 and PCH3031A are powerful tools designed to meet the demands of professionals and DIY enthusiasts alike. Both products embody Porter-Cable's commitment to innovation, efficiency, and precision, making them invaluable additions to any workshop or job site.

The Porter-Cable D26183-025-1 is a 5-inch random orbit sander known for its exceptional performance and user-friendly design. One of its main features is the high-performance 3.0 amp motor, which provides consistent power for a variety of sanding applications. This sander operates at a variable speed of up to 12,000 orbits per minute, allowing users to adjust the speed according to their specific sanding needs. The tool’s design minimizes vibration, enhancing user comfort during extended periods of use.

Additionally, the D26183-025-1 features a dual-plane counterbalance for reduced vibration, which contributes to better control and smoother operation. The convenient dust collection system is another highlight, as it efficiently collects dust, keeping the workspace cleaner and reducing cleanup time. A dust-sealed switch further protects the tool's components from debris, ensuring a longer lifespan.

On the other hand, the PCH3031A is a robust motor and generator combination designed for versatility and durability. This unit is equipped with an efficient engine that provides reliable power, making it suitable for construction sites and outdoor projects where portable power is essential. An integrated inverter ensures clean, stable power, which is crucial for sensitive electronics and appliances.

Key characteristics of the PCH3031A include multiple outlet options, allowing users to connect different devices simultaneously with ease. Its compact, lightweight design enables easy transportation, while the rugged construction withstands the rigors of daily use. The tool's low noise output is a significant advantage, making it a great choice for indoor applications without disturbing the surrounding environment.

Together, the Porter-Cable D26183-025-1 and PCH3031A represent the brand's dedication to combining power with practicality. They are meticulously designed to enhance productivity, making them essential tools for professionals aiming to achieve high-quality results in various sanding and power supply tasks. Each product reflects an emphasis on user comfort, reliability, and performance, reinforcing Porter-Cable's reputation as a leader in the tools market.
Top Page Image Contents