Porter-Cable D26183-025-1, PCH3031A instruction manual To Siphon CHEMICALS/CLEANING Solvents

Page 11

TO SIPHON CHEMICALS/CLEANING SOLVENTS

Siphoning chemicals or cleaning solvents is a low pressure operation.

NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach.

1. Press chemical hose onto barbed fitting located

Barbed

near high pressure hose connection of pump as

Fitting

shown.

 

 

2.Place other end of chemical hose with filter on it into container holding chemical/cleaning solution.

3.Install low pressure (black) nozzle into quick connect fitting of wand, see How To Use Wand paragraph in this section.

4.After use of chemical, siphon clean water through chemical hose to rinse it and pump clean. Chemicals which remain in pump can damage it. Damage to

pump due to chemicals will not be covered under warranty.

NOTE: Chemicals and soap will not siphon when wand is in the high pressure setting.

READ AND UNDERSTAND ALL WARNINGS BEFORE STARTING UNIT

When using the high pressure setting, DO NOT allow the high pressure spray to come in contact with unprotected skin,

eyes, or with any pets or animals. Serious injury can occur.

Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately!

Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank.

Never fill fuel tank completely. Fill tank to 1/2" below bottom of filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine.

Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty.

Never pull water supply hose to move pressure washer. This could damage hose and/or pump inlet.

DO NOT use hot water, use cold water only.

Never turn water supply off while pressure washer engine is running or damage to pump will result.

DO NOT stop spraying water for more than two minutes at a time. Pump operates in bypass mode when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged.

If you do not understand these precautions please call 1-888-559-8550 to speak to a service representative for further instructions.

11- ENG

D26183

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Instruction General Information Important Safety Instructions Safety Guidelines / DefinitionsHazard What can Happen Risk Unsafe Operation BOX Contents Assembly Throttle Control Lever Controls engine speed OperationBasic Elements of Engine Pressure WasherPressure Washer Terminology HOW to USETo Adjust Pressure To USE Wand Press chemical hose onto barbed fitting located To Siphon CHEMICALS/CLEANING SolventsRead and Understand ALL Warnings Before Starting Unit Cone side faces out StartingTo Shut Down Verify the filter screen is in water inlet of pump. NotePump MaintenanceHow To Change Pump Oil EngineWand HOW to Clean the Water Inlet FilterWindshield washer fluid may also be used StorageEngine Pump Problem Causecorrection Trouble Shooting GuideCorrection ProblemCause Responsibility of Original Purchaser initial User Limited WarrantyENG D26183 Call Quick Facts

PCH3031A, D26183-025-1 specifications

The Porter-Cable D26183-025-1 and PCH3031A are powerful tools designed to meet the demands of professionals and DIY enthusiasts alike. Both products embody Porter-Cable's commitment to innovation, efficiency, and precision, making them invaluable additions to any workshop or job site.

The Porter-Cable D26183-025-1 is a 5-inch random orbit sander known for its exceptional performance and user-friendly design. One of its main features is the high-performance 3.0 amp motor, which provides consistent power for a variety of sanding applications. This sander operates at a variable speed of up to 12,000 orbits per minute, allowing users to adjust the speed according to their specific sanding needs. The tool’s design minimizes vibration, enhancing user comfort during extended periods of use.

Additionally, the D26183-025-1 features a dual-plane counterbalance for reduced vibration, which contributes to better control and smoother operation. The convenient dust collection system is another highlight, as it efficiently collects dust, keeping the workspace cleaner and reducing cleanup time. A dust-sealed switch further protects the tool's components from debris, ensuring a longer lifespan.

On the other hand, the PCH3031A is a robust motor and generator combination designed for versatility and durability. This unit is equipped with an efficient engine that provides reliable power, making it suitable for construction sites and outdoor projects where portable power is essential. An integrated inverter ensures clean, stable power, which is crucial for sensitive electronics and appliances.

Key characteristics of the PCH3031A include multiple outlet options, allowing users to connect different devices simultaneously with ease. Its compact, lightweight design enables easy transportation, while the rugged construction withstands the rigors of daily use. The tool's low noise output is a significant advantage, making it a great choice for indoor applications without disturbing the surrounding environment.

Together, the Porter-Cable D26183-025-1 and PCH3031A represent the brand's dedication to combining power with practicality. They are meticulously designed to enhance productivity, making them essential tools for professionals aiming to achieve high-quality results in various sanding and power supply tasks. Each product reflects an emphasis on user comfort, reliability, and performance, reinforcing Porter-Cable's reputation as a leader in the tools market.
Top Page Image Contents