Porter-Cable PCH3031A, D26183-025-1 Trouble Shooting Guide, Problem Causecorrection

Page 16

TROUBLE SHOOTING GUIDE

PROBLEM

CAUSECORRECTION

Engine will not start (see Engine Manual for further engine troubleshooting)

No or low pressure (initial use)

No fuel.

Low oil (if equipped with low oil shutdown).

Pressure builds up after two pulls on the recoil starter or after initial use.

Not primed or choked.

Spark plug wire not attached.

Engine ON/OFF switch in OFF po- sition (If applicable.)

Choke lever in the “Choke” position on a “hot” engine or an engine that has been exposed to thermal heat for a long period of time.

Fuel valve closed (if equipped)

Wand not in high pressure.

Low water supply.

Leak at high pressure hose.

Nozzle obstructed.

Water filter screen clogged.

Defective E-Z start valve.

Air in hose.

Choke lever in the “Choke” position.

Throttle control lever is not in the “Fast” position. (if equipped)

High pressure hose is too long.

Add Fuel.

Add required amount of oil.

Squeeze gun trigger to relieve pressure.

Push primer bulb 3 times or choke engine.

Attach spark plug wire.

Place engine ON/OFF switch in on position.

Move choke to the “No Choke” position.

Move the fuel valve lever to the “Open” position.

See How to Use Wand paragraph in the Operation Section.

Water supply must be at least 5 GPM @ 20 PSI.

Repair leak. Apply sealant tape if necessary.

Clean nozzle with paper clip or nozzle cleaning tool, pour water into nozzle end to flush out ob- struction.

Remove and clean filter.

Check with Authorized Warranty Service Center (AWSC.)

Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Reconnect water source to pump inlet and turn on water source. Squeeze trigger to re- move remaining air

Move choke to the “No Choke” position.

Move throttle control lever to the “Fast” position.

Use high pressure hose under 100 feet.

D26183

16- ENG

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Instruction General Information Safety Guidelines / Definitions Important Safety InstructionsHazard What can Happen Risk Unsafe Operation BOX Contents Assembly Operation Basic Elements of EnginePressure Washer Throttle Control Lever Controls engine speedTo Adjust Pressure HOW to USEPressure Washer Terminology To USE Wand Read and Understand ALL Warnings Before Starting Unit To Siphon CHEMICALS/CLEANING SolventsPress chemical hose onto barbed fitting located Starting To Shut DownVerify the filter screen is in water inlet of pump. Note Cone side faces outMaintenance How To Change Pump OilEngine PumpHOW to Clean the Water Inlet Filter WandEngine Pump StorageWindshield washer fluid may also be used Trouble Shooting Guide Problem CausecorrectionCause ProblemCorrection Limited Warranty Responsibility of Original Purchaser initial UserENG D26183 Quick Facts Call

PCH3031A, D26183-025-1 specifications

The Porter-Cable D26183-025-1 and PCH3031A are powerful tools designed to meet the demands of professionals and DIY enthusiasts alike. Both products embody Porter-Cable's commitment to innovation, efficiency, and precision, making them invaluable additions to any workshop or job site.

The Porter-Cable D26183-025-1 is a 5-inch random orbit sander known for its exceptional performance and user-friendly design. One of its main features is the high-performance 3.0 amp motor, which provides consistent power for a variety of sanding applications. This sander operates at a variable speed of up to 12,000 orbits per minute, allowing users to adjust the speed according to their specific sanding needs. The tool’s design minimizes vibration, enhancing user comfort during extended periods of use.

Additionally, the D26183-025-1 features a dual-plane counterbalance for reduced vibration, which contributes to better control and smoother operation. The convenient dust collection system is another highlight, as it efficiently collects dust, keeping the workspace cleaner and reducing cleanup time. A dust-sealed switch further protects the tool's components from debris, ensuring a longer lifespan.

On the other hand, the PCH3031A is a robust motor and generator combination designed for versatility and durability. This unit is equipped with an efficient engine that provides reliable power, making it suitable for construction sites and outdoor projects where portable power is essential. An integrated inverter ensures clean, stable power, which is crucial for sensitive electronics and appliances.

Key characteristics of the PCH3031A include multiple outlet options, allowing users to connect different devices simultaneously with ease. Its compact, lightweight design enables easy transportation, while the rugged construction withstands the rigors of daily use. The tool's low noise output is a significant advantage, making it a great choice for indoor applications without disturbing the surrounding environment.

Together, the Porter-Cable D26183-025-1 and PCH3031A represent the brand's dedication to combining power with practicality. They are meticulously designed to enhance productivity, making them essential tools for professionals aiming to achieve high-quality results in various sanding and power supply tasks. Each product reflects an emphasis on user comfort, reliability, and performance, reinforcing Porter-Cable's reputation as a leader in the tools market.
Top Page Image Contents