Porter-Cable DBSI325 instruction manual Quick Facts

Page 22

QUICK FACTS

CALL 1-888-559-8550 TO FIND A LOCAL AUTHORIZED SERVICE CENTER NEAR YOU FOR REPAIRS AND SERVICE PART PURCHASES

ENGINE

GAS

ENGINE OIL

WATTAGE

WIRING

BATTERY

VOLT REG.

ENGINE

STORAGE

OPERATION

Use clean, fresh gasoline with a minimum 87 octane rating. Do not add gasoline during or immediately after use.

Refer to engine owner's manual for oil recommendations. Most generators are equipped with a low-oil shutdown. If the oil is low or if the Generator is not level, the engine will not start.

Make wattage calculations before use. Refer to general operator's manual for further instructions.

Contact an electrician for any wiring instructions. If wiring into a house, a double-throw transfer switch and a heavy duty cord set must be used.

Use a standard (12V) lawn and garden battery with a minimum of 45 A.H. or 210 CCA.

The voltage and frequency are regulated by the rpm's of the engine. Do not adjust the throttle or governor to achieve higher performance. This will only alter the factory Pre-set settings and damage anything connected to the generator.

Be sure a volt/amp surge protector is used when sensitive electronic equipment is used, such as: televisions, computers, stereos, and etc… The damage of such equipment without the use of a protector WILL NOT be covered under warranty.

Do not adjust or attempt maintenance without consulting engine manual or an authorized engine service center.

Add stabilizer to fuel tank and run engine for 5 minutes before storage.

When in long term storage, operate the generator every 60 days for at least 10 minutes with a load on it. This will prevent the loss of residual magnetism that produces the electricity.

Allow the generator to run 5 minutes at no load for the engine and the gen head to stabilize.

Make sure the adequate size of extension cord is used. Refer to the Grounding Instructions/Extension Cord section of the owners manual.

If the generator is operating equipment that is drawing half of the rated watts it is considered 50% load. Using all of the rated watts is considered 100% load.

ALWAYS REFER TO THE MANUALS SUPPLIED WITH THIS UNIT

D26608

22- ENG

Page 21 Page 22
Image 22
Page 21 Page 22
Contents Generator Consumer General and Service Information Consumer Safety InformationWhen installing a Double Safety Guidelines / DefinitionsImportant Safety Instructions Risk of Electrocution and FireOperation When damagedRisk of Electrocution and Fire Generator in rainUnit Indoors or in ANY Risk of FireConfined Area Risk of Breathing Inhalation Hazard Risk of Unsafe OperationRisk of HOT Surfaces Risk of Moving Parts SpecificationsRisk from Lifting Other Loose Parts AssemblyRemove Generator from Carton Grounding the GeneratorDouble Throw Transfer Switch Extension CordsGenerator Capacity OperationKnow Your Generator Circuit BreakersTo Start the Engine Connecting Electrical Loads Generator Maintenance MaintenanceEngine Maintenance Customer Responsibilities TableEngine Preparation StorageGenerator Wattage Calculations Determining Wattage RequirementsApplication Guide Starting Wattage RequirementsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide StartLimited Warranty Responsibility of Original Purchaser initial UserENG D26608 Quick Facts

DBSI325 specifications

The Porter-Cable DBSI325 is a highly versatile and powerful tool designed for contractors and DIY enthusiasts alike. Known for its innovative features and robust performance, this tool has gained a reputation for efficiency and reliability.

One of the standout features of the DBSI325 is its compact and lightweight design, which makes it easy to maneuver in tight spaces. Weighing in at just a few pounds, this tool allows for extended use without causing fatigue, vital for long working hours. The ergonomic handle provides a comfortable grip, ensuring precise control during operation.

This tool is equipped with a powerful motor that delivers a maximum speed, providing users with the ability to tackle a variety of tasks with ease. Whether you’re drilling through wood, metal, or masonry, the DBSI325 can handle the job. The speed settings are adjustable, allowing for greater versatility and adjustment based on the material being drilled.

Another key feature of the DBSI325 is its durable construction. Built with high-quality materials, the tool is designed to withstand the rigors of daily use on job sites. The durable housing protects the internal components, ensuring a long lifespan and minimizing the need for repairs.

Incorporating advanced technologies, the DBSI325 features a unique torque management system. This technology helps prevent over-torquing, protecting both the tool and the workpiece during operation. Additionally, the model includes a keyless chuck, which allows for quick and easy bit changes, enhancing efficiency and reducing downtime.

The depth adjustment system is another notable characteristic of the DBSI325. This feature provides precise control over drilling depth, ensuring consistent results across different projects. Whether you’re working on furniture assembly or home improvement tasks, this tool offers the accuracy required for professional-grade results.

Porter-Cable is recognized for its dedication to customer satisfaction, offering a warranty that reflects their commitment to quality. The DBSI325 is emblematic of this ethos, combining performance, durability, and user-friendly design into a single powerful tool.

In summary, the Porter-Cable DBSI325 stands out as a versatile and durable tool suitable for various applications. With its powerful motor, ergonomic design, advanced technologies, and strong construction, it is an essential addition to any toolbox, providing the performance needed to complete tasks efficiently and effectively. Whether you’re a seasoned professional or a weekend warrior, the DBSI325 is sure to meet your drilling needs.
Top Page Image Contents