Poulan 183249 To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

 

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT

LIFT LEVER

HIGH POSITION

LOW

POSITION

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PR1842STB IV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesContents of Hardware Pack Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DISCHARG- INGCheck Tire Pressure Check Deck LevelnessBattery Reverse Forward Fast See Safety Rules SectionEngine on Engine OFF OIL Pressure Lights on LightKnow Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine ADD GasolineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart General RecommendationsBefore Each USE Tractor Clean AIR Screen EngineBelts Transaxle CoolingCleaning MufflerSpark Plugs Engine OIL FilterTo Install Mower See Fig To Remove Mower See FigTo Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseOther Fuel SystemEngine OIL CylindersTroubleshooting Points OFF Schematic Tractor - Model Number PR1842STB Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Repair Parts Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Fold Along This Dotted Line Degree Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183249 specifications

The Poulan 183249 is a standout offering in the realm of outdoor power equipment, specifically designed for homeowners and landscape professionals alike. Reliable and efficient, this model demonstrates Poulan’s commitment to quality and performance in its category.

One of the primary features of the Poulan 183249 is its powerful engine. Running on a robust two-cycle, 33cc engine, it delivers the necessary power to handle a variety of applications, from light trimming to more demanding yard work. The engine's design focuses not only on performance but also on fuel efficiency, ensuring that users can work longer without frequent refueling.

In terms of usability, the Poulan 183249 is equipped with an ergonomic handle that provides comfort during extended use. This thoughtful design helps to reduce user fatigue and enhances control, making it easier to navigate through different terrains. The adjustable shaft length further accommodates various user heights, allowing for a more personalized operation experience.

The trimming system of the Poulan 183249 features a dual-line feed, which significantly improves trimming efficiency. This system allows for quicker cuts, enabling users to tackle large lawns or garden beds in a shorter amount of time. Additionally, the automatic line feed mechanism ensures that the user doesn’t need to stop working to reload the line, facilitating a smoother workflow.

Another notable feature is the incorporation of the Easy Start technology. This system minimizes the effort required to startup the engine with fewer pulls, alleviating the common frustrations associated with starting small engines. This is particularly appealing for those who may lack physical strength or experience in operating string trimmers.

For durability, the Poulan 183249 is built with high-quality materials that can withstand outdoor conditions. Its weather-resistant components enhance longevity, making it a reliable tool for seasonal use. Users appreciate the low-vibration design as this reduces strain on the hands and arms while operating, further enhancing comfort during use.

In conclusion, the Poulan 183249 is a versatile and powerful trimmer that is well-suited for both casual users and gardening professionals. Its combination of a robust engine, ergonomic design, efficient trimming system, and user-friendly features like Easy Start technology makes it a worthy addition to any gardening toolkit, ensuring users can maintain their yards effectively and with ease.
Top Page Image Contents