Poulan 183249 owner manual To Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

IDLER PULLEYS

MANDREL PULLEYS

FIG. 23

TO ADJUST BRAKE (See Fig. 24)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE

1-1/2"“ENGAGED”

NUT “A”

JAM

NUT

OPERATING

ARM

FIG. 24

TO REPLACE MOTION DRIVE BELT (See Fig. 25)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down between transaxle belt keepers and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSAXLE

PULLEY

FIG. 25

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 26

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PR1842STB Safe Operation Practices for Ride-On Mowers IV. ServiceGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsContents of Hardware Pack HOW to SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To Convert to Bagging or DISCHARG- ING To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessSee Safety Rules Section Battery Reverse Forward FastEngine on Engine OFF OIL Pressure Lights on LightKnow Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMulching Mowing Tips Mowing TipsLubrication Chart General RecommendationsBefore Each USE Tractor Engine Clean AIR ScreenBelts Transaxle CoolingMuffler CleaningSpark Plugs Engine OIL FilterTo Remove Mower See Fig To Install Mower See FigBelt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig To Adjust Steering Wheel AlignmentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseFuel System OtherEngine OIL CylindersTroubleshooting Points OFF Tractor - Model Number PR1842STB Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Repair Parts Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line DegreeParts and Service

183249 specifications

The Poulan 183249 is a standout offering in the realm of outdoor power equipment, specifically designed for homeowners and landscape professionals alike. Reliable and efficient, this model demonstrates Poulan’s commitment to quality and performance in its category.

One of the primary features of the Poulan 183249 is its powerful engine. Running on a robust two-cycle, 33cc engine, it delivers the necessary power to handle a variety of applications, from light trimming to more demanding yard work. The engine's design focuses not only on performance but also on fuel efficiency, ensuring that users can work longer without frequent refueling.

In terms of usability, the Poulan 183249 is equipped with an ergonomic handle that provides comfort during extended use. This thoughtful design helps to reduce user fatigue and enhances control, making it easier to navigate through different terrains. The adjustable shaft length further accommodates various user heights, allowing for a more personalized operation experience.

The trimming system of the Poulan 183249 features a dual-line feed, which significantly improves trimming efficiency. This system allows for quicker cuts, enabling users to tackle large lawns or garden beds in a shorter amount of time. Additionally, the automatic line feed mechanism ensures that the user doesn’t need to stop working to reload the line, facilitating a smoother workflow.

Another notable feature is the incorporation of the Easy Start technology. This system minimizes the effort required to startup the engine with fewer pulls, alleviating the common frustrations associated with starting small engines. This is particularly appealing for those who may lack physical strength or experience in operating string trimmers.

For durability, the Poulan 183249 is built with high-quality materials that can withstand outdoor conditions. Its weather-resistant components enhance longevity, making it a reliable tool for seasonal use. Users appreciate the low-vibration design as this reduces strain on the hands and arms while operating, further enhancing comfort during use.

In conclusion, the Poulan 183249 is a versatile and powerful trimmer that is well-suited for both casual users and gardening professionals. Its combination of a robust engine, ergonomic design, efficient trimming system, and user-friendly features like Easy Start technology makes it a worthy addition to any gardening toolkit, ensuring users can maintain their yards effectively and with ease.
Top Page Image Contents