Poulan 183249 To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 19

SUSPENSION

ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 21

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 22

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 23)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PR1842STB IV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesContents of Hardware Pack Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DISCHARG- INGCheck Tire Pressure Check Deck LevelnessBattery Reverse Forward Fast See Safety Rules SectionEngine on Engine OFF OIL Pressure Lights on LightKnow Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine ADD GasolineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Tractor Clean AIR Screen EngineBelts Transaxle CoolingCleaning MufflerSpark Plugs Engine OIL FilterTo Install Mower See Fig To Remove Mower See FigTo Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseOther Fuel SystemEngine OIL CylindersTroubleshooting Points OFF Schematic Tractor - Model Number PR1842STB Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Repair Parts Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Fold Along This Dotted Line Degree Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183249 specifications

The Poulan 183249 is a standout offering in the realm of outdoor power equipment, specifically designed for homeowners and landscape professionals alike. Reliable and efficient, this model demonstrates Poulan’s commitment to quality and performance in its category.

One of the primary features of the Poulan 183249 is its powerful engine. Running on a robust two-cycle, 33cc engine, it delivers the necessary power to handle a variety of applications, from light trimming to more demanding yard work. The engine's design focuses not only on performance but also on fuel efficiency, ensuring that users can work longer without frequent refueling.

In terms of usability, the Poulan 183249 is equipped with an ergonomic handle that provides comfort during extended use. This thoughtful design helps to reduce user fatigue and enhances control, making it easier to navigate through different terrains. The adjustable shaft length further accommodates various user heights, allowing for a more personalized operation experience.

The trimming system of the Poulan 183249 features a dual-line feed, which significantly improves trimming efficiency. This system allows for quicker cuts, enabling users to tackle large lawns or garden beds in a shorter amount of time. Additionally, the automatic line feed mechanism ensures that the user doesn’t need to stop working to reload the line, facilitating a smoother workflow.

Another notable feature is the incorporation of the Easy Start technology. This system minimizes the effort required to startup the engine with fewer pulls, alleviating the common frustrations associated with starting small engines. This is particularly appealing for those who may lack physical strength or experience in operating string trimmers.

For durability, the Poulan 183249 is built with high-quality materials that can withstand outdoor conditions. Its weather-resistant components enhance longevity, making it a reliable tool for seasonal use. Users appreciate the low-vibration design as this reduces strain on the hands and arms while operating, further enhancing comfort during use.

In conclusion, the Poulan 183249 is a versatile and powerful trimmer that is well-suited for both casual users and gardening professionals. Its combination of a robust engine, ergonomic design, efficient trimming system, and user-friendly features like Easy Start technology makes it a worthy addition to any gardening toolkit, ensuring users can maintain their yards effectively and with ease.
Top Page Image Contents