Poulan 183249 owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

SEAT PAN

FIG. 29

HOOD

HEADLIGHT WIRE CONNECTOR

TERMINAL

KEPS NUT

COVER

 

HEX

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 30

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 32)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

GOVERNOR GOVERNOR

CONTROL LEVER CONTROL PLATE

HOLES “A”

CLAMP

THROTTLE

 

 

SCREW

CABLE

FIG. 32

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y

23ADJUSTMENTS.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PR1842STB II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationTable of Contents Customer Responsibilities Product SpecificationsContents of Hardware Pack Before Removing Tractor from Skid Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or DISCHARG- ING Check Tire PressureLight Battery Reverse Forward FastSee Safety Rules Section Engine on Engine OFF OIL Pressure Lights onKnow Your Tractor HOW to USE Your Tractor To Transport To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineADD Gasoline Check Engine OIL LevelMulching Mowing Tips Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Tractor Transaxle Cooling Clean AIR ScreenEngine BeltsEngine OIL Filter CleaningMuffler Spark PlugsTo Remove Mower See Fig To Install Mower See FigBelt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig Front Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysCylinders OtherFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PR1842STB Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Repair Parts Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line DegreeParts and Service

183249 specifications

The Poulan 183249 is a standout offering in the realm of outdoor power equipment, specifically designed for homeowners and landscape professionals alike. Reliable and efficient, this model demonstrates Poulan’s commitment to quality and performance in its category.

One of the primary features of the Poulan 183249 is its powerful engine. Running on a robust two-cycle, 33cc engine, it delivers the necessary power to handle a variety of applications, from light trimming to more demanding yard work. The engine's design focuses not only on performance but also on fuel efficiency, ensuring that users can work longer without frequent refueling.

In terms of usability, the Poulan 183249 is equipped with an ergonomic handle that provides comfort during extended use. This thoughtful design helps to reduce user fatigue and enhances control, making it easier to navigate through different terrains. The adjustable shaft length further accommodates various user heights, allowing for a more personalized operation experience.

The trimming system of the Poulan 183249 features a dual-line feed, which significantly improves trimming efficiency. This system allows for quicker cuts, enabling users to tackle large lawns or garden beds in a shorter amount of time. Additionally, the automatic line feed mechanism ensures that the user doesn’t need to stop working to reload the line, facilitating a smoother workflow.

Another notable feature is the incorporation of the Easy Start technology. This system minimizes the effort required to startup the engine with fewer pulls, alleviating the common frustrations associated with starting small engines. This is particularly appealing for those who may lack physical strength or experience in operating string trimmers.

For durability, the Poulan 183249 is built with high-quality materials that can withstand outdoor conditions. Its weather-resistant components enhance longevity, making it a reliable tool for seasonal use. Users appreciate the low-vibration design as this reduces strain on the hands and arms while operating, further enhancing comfort during use.

In conclusion, the Poulan 183249 is a versatile and powerful trimmer that is well-suited for both casual users and gardening professionals. Its combination of a robust engine, ergonomic design, efficient trimming system, and user-friendly features like Easy Start technology makes it a worthy addition to any gardening toolkit, ensuring users can maintain their yards effectively and with ease.
Top Page Image Contents