Poulan 183247, PR2042 owner manual Mulching Mowing Tips

Page 14

OPERATION

MOWING TIPS

Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

The left hand side of mower should be used for trimming.

Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 9).

If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

Always operate engine at full throttle when mowing to assure better mowing performance and proper dis- charge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting perfor- mance as well as the quality of cut desired.

When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

FIG. 9

MULCHING MOWING TIPS

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN AFTER EACH USE.

The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades.

Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried and the newly cut area will not be exposed to the direct sun.

For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades (See Fig. 10). For extremely heavy mulching, reduce your width of cut on each pass and mow slowly.

Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across or perpendicular to the first cut path.

Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn.

MAX 1/3

FIG. 10

14

Image 14
Contents PR2042 PPR2042STB General Operation Safety RulesIV. Service II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesSeat Unassembled HardwareSteering Wheel Slope Sheet KeysHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsBefore Each USE General Recommendations Lubrication ChartCustomer Responsibilities Tractor Engine Muffler CleaningAIR Filter See Fig Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor Model Number PR2042 PPR2042STB, Product no 56Electrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresSpark Arrester EngineOptional Equipment 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183247, PR2042 specifications

The Poulan PR2042,183247 is an impressive gas-powered chainsaw designed for homeowners and light-duty professionals who need a reliable tool for cutting tasks. This model is part of the popular Poulan line, known for its durability and performance, making it a popular choice for users looking for an efficient chainsaw to handle various outdoor projects.

One of the standout features of the PR2042 is its powerful 40cc 2-cycle engine. This engine delivers robust performance, allowing the chainsaw to cut through thick branches and logs with ease. The engine also has a relatively lightweight design, making it easier for users to maneuver the chainsaw without feeling fatigued during extended use.

The PR2042 comes with a 16-inch bar and chain, which strikes the perfect balance between reach and control. This length is ideal for tasks such as pruning trees, cutting firewood, and tackling storm damage. The chain is designed for fast cutting and easy maintenance, ensuring users can keep their chainsaw in top working condition with minimal effort.

In terms of technology, the Poulan PR2042 features an automatic chain oiler. This system ensures that the chain receives a steady supply of lubrication while in operation, reducing friction and prolonging the life of both the chain and the bar. Users can adjust the oil flow to match their cutting needs, which enhances efficiency and overall performance.

Another notable characteristic is the user's comfort and ease of use. The PR2042 is designed with anti-vibration technology, which minimizes the vibrations felt by the user, making the chainsaw more comfortable for prolonged use. Additionally, the ergonomic handle provides a secure grip, promoting better control and accuracy during cuts.

Safety features are also prioritized in the design of the Poulan PR2042. It comes equipped with a chain brake that helps prevent accidental chain movement, while the safety throttle ensures the chainsaw only operates when intended. These features provide peace of mind for users, whether they are experienced chainsaw operators or novices.

Overall, the Poulan PR2042,183247 chain saw is an excellent choice for those seeking a blend of power, convenience, and safety. Its robust engine, user-friendly design, and innovative features make it a reliable tool for managing a variety of cutting tasks, ensuring users can confidently tackle their outdoor projects.