Poulan PR2042, 183247 owner manual Install Seat See Fig

Page 7

ASSEMBLY

SEAT PAN

LABEL

FIG. 2

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Opera- tion section, page 10, for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

•Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Opera- tion section, page 10, for location and func- tion of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place gear shift lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine. After engine has started, move throttle control to idle position.

•Depress clutch/brake pedal into full “BRAKE” position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position.

•Turn ignition key to “OFF” position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PR2042 PPR2042STB II. Slope Operation Safety RulesIV. Service General OperationTable of Contents Customer Responsibilities Product SpecificationsSlope Sheet Keys Unassembled HardwareSteering Wheel SeatTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Transport To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsCustomer Responsibilities General Recommendations Lubrication ChartBefore Each USE Tractor Engine Spark Plugs CleaningAIR Filter See Fig MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWhen operator leaves Tractor Model Number PR2042 PPR2042STB, Product no 56 SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsOptional Equipment EngineSpark Arrester 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183247, PR2042 specifications

The Poulan PR2042,183247 is an impressive gas-powered chainsaw designed for homeowners and light-duty professionals who need a reliable tool for cutting tasks. This model is part of the popular Poulan line, known for its durability and performance, making it a popular choice for users looking for an efficient chainsaw to handle various outdoor projects.

One of the standout features of the PR2042 is its powerful 40cc 2-cycle engine. This engine delivers robust performance, allowing the chainsaw to cut through thick branches and logs with ease. The engine also has a relatively lightweight design, making it easier for users to maneuver the chainsaw without feeling fatigued during extended use.

The PR2042 comes with a 16-inch bar and chain, which strikes the perfect balance between reach and control. This length is ideal for tasks such as pruning trees, cutting firewood, and tackling storm damage. The chain is designed for fast cutting and easy maintenance, ensuring users can keep their chainsaw in top working condition with minimal effort.

In terms of technology, the Poulan PR2042 features an automatic chain oiler. This system ensures that the chain receives a steady supply of lubrication while in operation, reducing friction and prolonging the life of both the chain and the bar. Users can adjust the oil flow to match their cutting needs, which enhances efficiency and overall performance.

Another notable characteristic is the user's comfort and ease of use. The PR2042 is designed with anti-vibration technology, which minimizes the vibrations felt by the user, making the chainsaw more comfortable for prolonged use. Additionally, the ergonomic handle provides a secure grip, promoting better control and accuracy during cuts.

Safety features are also prioritized in the design of the Poulan PR2042. It comes equipped with a chain brake that helps prevent accidental chain movement, while the safety throttle ensures the chainsaw only operates when intended. These features provide peace of mind for users, whether they are experienced chainsaw operators or novices.

Overall, the Poulan PR2042,183247 chain saw is an excellent choice for those seeking a blend of power, convenience, and safety. Its robust engine, user-friendly design, and innovative features make it a reliable tool for managing a variety of cutting tasks, ensuring users can confidently tackle their outdoor projects.
Top Page Image Contents