Poulan 183247, PR2042 owner manual Tractor

Page 16

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

TRAILING EDGE UP

BLADE

MANDREL ASSEMBLY

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

FLAT WASHER

LOCK WASHER

CENTER

HOLE

STAR

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 11)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer secur- ing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 11

TO SHARPEN BLADE (See Fig. 12)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with bal- ancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 12

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PR2042 PPR2042STB Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Hardware Steering WheelSeat Slope Sheet KeysAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsCustomer Responsibilities General Recommendations Lubrication ChartBefore Each USE Tractor Engine Cleaning AIR Filter See FigMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor Model Number PR2042 PPR2042STB, Product no 56Electrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresOptional Equipment EngineSpark Arrester 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183247, PR2042 specifications

The Poulan PR2042,183247 is an impressive gas-powered chainsaw designed for homeowners and light-duty professionals who need a reliable tool for cutting tasks. This model is part of the popular Poulan line, known for its durability and performance, making it a popular choice for users looking for an efficient chainsaw to handle various outdoor projects.

One of the standout features of the PR2042 is its powerful 40cc 2-cycle engine. This engine delivers robust performance, allowing the chainsaw to cut through thick branches and logs with ease. The engine also has a relatively lightweight design, making it easier for users to maneuver the chainsaw without feeling fatigued during extended use.

The PR2042 comes with a 16-inch bar and chain, which strikes the perfect balance between reach and control. This length is ideal for tasks such as pruning trees, cutting firewood, and tackling storm damage. The chain is designed for fast cutting and easy maintenance, ensuring users can keep their chainsaw in top working condition with minimal effort.

In terms of technology, the Poulan PR2042 features an automatic chain oiler. This system ensures that the chain receives a steady supply of lubrication while in operation, reducing friction and prolonging the life of both the chain and the bar. Users can adjust the oil flow to match their cutting needs, which enhances efficiency and overall performance.

Another notable characteristic is the user's comfort and ease of use. The PR2042 is designed with anti-vibration technology, which minimizes the vibrations felt by the user, making the chainsaw more comfortable for prolonged use. Additionally, the ergonomic handle provides a secure grip, promoting better control and accuracy during cuts.

Safety features are also prioritized in the design of the Poulan PR2042. It comes equipped with a chain brake that helps prevent accidental chain movement, while the safety throttle ensures the chainsaw only operates when intended. These features provide peace of mind for users, whether they are experienced chainsaw operators or novices.

Overall, the Poulan PR2042,183247 chain saw is an excellent choice for those seeking a blend of power, convenience, and safety. Its robust engine, user-friendly design, and innovative features make it a reliable tool for managing a variety of cutting tasks, ensuring users can confidently tackle their outdoor projects.
Top Page Image Contents