Poulan 183247 To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 17

SUSPENSION ARM

LIFT LINK ADJUSTMENT

NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position. Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PR2042 PPR2042STB Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Hardware Steering WheelSeat Slope Sheet KeysAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsBefore Each USE General Recommendations Lubrication ChartCustomer Responsibilities Tractor Engine Cleaning AIR Filter See FigMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor Model Number PR2042 PPR2042STB, Product no 56Electrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresSpark Arrester EngineOptional Equipment 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183247, PR2042 specifications

The Poulan PR2042,183247 is an impressive gas-powered chainsaw designed for homeowners and light-duty professionals who need a reliable tool for cutting tasks. This model is part of the popular Poulan line, known for its durability and performance, making it a popular choice for users looking for an efficient chainsaw to handle various outdoor projects.

One of the standout features of the PR2042 is its powerful 40cc 2-cycle engine. This engine delivers robust performance, allowing the chainsaw to cut through thick branches and logs with ease. The engine also has a relatively lightweight design, making it easier for users to maneuver the chainsaw without feeling fatigued during extended use.

The PR2042 comes with a 16-inch bar and chain, which strikes the perfect balance between reach and control. This length is ideal for tasks such as pruning trees, cutting firewood, and tackling storm damage. The chain is designed for fast cutting and easy maintenance, ensuring users can keep their chainsaw in top working condition with minimal effort.

In terms of technology, the Poulan PR2042 features an automatic chain oiler. This system ensures that the chain receives a steady supply of lubrication while in operation, reducing friction and prolonging the life of both the chain and the bar. Users can adjust the oil flow to match their cutting needs, which enhances efficiency and overall performance.

Another notable characteristic is the user's comfort and ease of use. The PR2042 is designed with anti-vibration technology, which minimizes the vibrations felt by the user, making the chainsaw more comfortable for prolonged use. Additionally, the ergonomic handle provides a secure grip, promoting better control and accuracy during cuts.

Safety features are also prioritized in the design of the Poulan PR2042. It comes equipped with a chain brake that helps prevent accidental chain movement, while the safety throttle ensures the chainsaw only operates when intended. These features provide peace of mind for users, whether they are experienced chainsaw operators or novices.

Overall, the Poulan PR2042,183247 chain saw is an excellent choice for those seeking a blend of power, convenience, and safety. Its robust engine, user-friendly design, and innovative features make it a reliable tool for managing a variety of cutting tasks, ensuring users can confidently tackle their outdoor projects.
Top Page Image Contents