Poulan 183113 Before Starting the Engine, Towing Carts and Other Attach, Ments, ADD Gasoline

Page 13

OPERATION

 

 

CAUTION: Alcohol blended fuels (called

 

gasohol or using ethanol or methanol)

 

can attract moisture which leads to sepa-

 

ration and formation of acids during

 

storage. Acidic gas can damage the fuel

 

system of an engine while in storage. To

 

avoid engine problems, the fuel system

 

should be emptied before storage of 30

 

days or longer. Drain the gas tank, start

 

the engine and let it run until the fuel

 

lines and carburetor are empty. Use

 

fresh fuel next season. See Storage

FIG. 9

Instructions for additional information.

Never use engine or carburetor cleaner

TOWING CARTS AND OTHER ATTACH-

products in the fuel tank or permanent

damage may occur.

MENTS

 

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

Check engine oil with tractor on level ground.

Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

To change engine oil, see the Customer Responsibilities section in this manual.

ADD GASOLINE

Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

Be sure freewheel control is in the transmission engaged position.

Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

Place motion control lever in neutral (N) position.

Move attachment clutch to “DISENGAGED” position.

Move throttle control to fast position

Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50° F and above)

When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

13

Image 13
Contents PR185H42STG IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingCheck Deck Levelness To Convert to Bagging or DischargingOperation Motion Control Lever Selects the speed Know Your TractorHOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other Attach Before Starting the EngineMents Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips Service Dates Lubrication ChartCustomer Responsibilities General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine Clean AIR INTAKE/COOLING Areas Clean AIR ScreenCleaning Engine OIL FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Fuse Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PR185H42STG Product no 56 SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsOptional Equipment EngineSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183113 specifications

The Poulan 183113 is a powerful and versatile chainsaw that is designed for both professional and casual users. Known for its durability and performance, this model is suitable for various cutting tasks, from pruning branches to felling trees.

One of the standout features of the Poulan 183113 is its engine, which boasts a robust 18-inch bar and a powerful two-cycle engine. This engine provides a balance of performance and efficiency, delivering enough power to handle tough cutting jobs while still being manageable for operators. Its lightweight design allows for easy handling and maneuverability, making it an excellent choice for extended use.

Equipped with advanced technologies, the Poulan 183113 utilizes an easy-start system that ensures reliable starting even in challenging conditions. This feature saves users time and frustration, allowing them to focus on their tasks rather than struggling with engine troubles. Additionally, the chainsaw employs a high-quality chain that provides smooth cutting action, ensuring precision and efficiency during operation.

Safety is also a priority with the Poulan 183113. It comes with various safety features, including a chain brake that immediately stops the chain when activated, reducing the risk of accidents. Moreover, the anti-vibration system minimizes user fatigue, making it comfortable to use over long periods.

The design of the Poulan 183113 emphasizes ease of maintenance. It features tool-less chain adjustment, making it simple for users to adjust the tension of the chain without the need for specialized tools. This means that operators can achieve the best performance from their chainsaw while ensuring the longevity of the cutting equipment.

In summary, the Poulan 183113 is an efficient chainsaw that combines a powerful engine, advanced starting technology, and thoughtful safety features. With its lightweight design and user-friendly maintenance options, it caters to a wide range of cutting needs, making it an ideal choice for both seasoned professionals and homeowners alike. Users can trust the Poulan 183113 to deliver consistent performance for all their cutting jobs.