Poulan 183113 owner manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 26

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

Clean entire tractor (See “CLEANING” in the Customer Responsibilities section of this manual).

Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

Lubricate as shown in the Customer Responsibilities section of this manual.

Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

Fully charge the battery for storage.

After a period of time in storage, battery may require recharging.

To help prevent corrosion and power leakage during long periods of storage, battery cables should be discon- nected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Customer Respon- sibilities section of this manual).

After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL

H O S E , O R T A N K D U R I N G S T O R A G E . A L S O , EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

Drain the fuel tank.

Start the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during stor- age. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Customer Responsibilities section of this manual).

CYLINDER(S)

Remove spark plug(s).

Pour one ounce of oil through spark plug hole(s) into cylinder(s).

Turn ignition key to “START” position for a few seconds to distribute oil.

Replace with new spark plug(s).

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your tractor indoors and cover it to give protection from dust and dirt.

Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

26

Image 26
Contents PR185H42STG General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingCheck Tire Pressure To Convert to Bagging or DischargingOperation Know Your Tractor Motion Control Lever Selects the speedHOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsMents Before Starting the EngineTowing Carts and Other Attach Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission Mulching Mowing Tips Customer Responsibilities Lubrication ChartService Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemEngine Cleaning Clean AIR ScreenClean AIR INTAKE/COOLING Areas Engine OIL FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorInterlocks and Relays Fuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR185H42STG Product no 56Electrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresSpark Arrester EngineOptional Equipment 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183113 specifications

The Poulan 183113 is a powerful and versatile chainsaw that is designed for both professional and casual users. Known for its durability and performance, this model is suitable for various cutting tasks, from pruning branches to felling trees.

One of the standout features of the Poulan 183113 is its engine, which boasts a robust 18-inch bar and a powerful two-cycle engine. This engine provides a balance of performance and efficiency, delivering enough power to handle tough cutting jobs while still being manageable for operators. Its lightweight design allows for easy handling and maneuverability, making it an excellent choice for extended use.

Equipped with advanced technologies, the Poulan 183113 utilizes an easy-start system that ensures reliable starting even in challenging conditions. This feature saves users time and frustration, allowing them to focus on their tasks rather than struggling with engine troubles. Additionally, the chainsaw employs a high-quality chain that provides smooth cutting action, ensuring precision and efficiency during operation.

Safety is also a priority with the Poulan 183113. It comes with various safety features, including a chain brake that immediately stops the chain when activated, reducing the risk of accidents. Moreover, the anti-vibration system minimizes user fatigue, making it comfortable to use over long periods.

The design of the Poulan 183113 emphasizes ease of maintenance. It features tool-less chain adjustment, making it simple for users to adjust the tension of the chain without the need for specialized tools. This means that operators can achieve the best performance from their chainsaw while ensuring the longevity of the cutting equipment.

In summary, the Poulan 183113 is an efficient chainsaw that combines a powerful engine, advanced starting technology, and thoughtful safety features. With its lightweight design and user-friendly maintenance options, it caters to a wide range of cutting needs, making it an ideal choice for both seasoned professionals and homeowners alike. Users can trust the Poulan 183113 to deliver consistent performance for all their cutting jobs.