Poulan 183113 owner manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 23

SERVICE AND ADJUSTMENTS

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (N) (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LOCK GATE

LEVER

 

 

ADJUSTMENT

 

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 27

23

Image 23
Contents PR185H42STG II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Motion Control Lever Selects the speed Know Your TractorHOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other Attach MentsAutomatic Transmission Warm UP Mowing TipsPurge Transmission Mulching Mowing Tips General Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresEngine Engine OIL Filter Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Replace Fuse To Adjust CarburetorInterlocks and Relays Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PR185H42STG Product no 56 SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsSpark Arrester EngineOptional Equipment 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183113 specifications

The Poulan 183113 is a powerful and versatile chainsaw that is designed for both professional and casual users. Known for its durability and performance, this model is suitable for various cutting tasks, from pruning branches to felling trees.

One of the standout features of the Poulan 183113 is its engine, which boasts a robust 18-inch bar and a powerful two-cycle engine. This engine provides a balance of performance and efficiency, delivering enough power to handle tough cutting jobs while still being manageable for operators. Its lightweight design allows for easy handling and maneuverability, making it an excellent choice for extended use.

Equipped with advanced technologies, the Poulan 183113 utilizes an easy-start system that ensures reliable starting even in challenging conditions. This feature saves users time and frustration, allowing them to focus on their tasks rather than struggling with engine troubles. Additionally, the chainsaw employs a high-quality chain that provides smooth cutting action, ensuring precision and efficiency during operation.

Safety is also a priority with the Poulan 183113. It comes with various safety features, including a chain brake that immediately stops the chain when activated, reducing the risk of accidents. Moreover, the anti-vibration system minimizes user fatigue, making it comfortable to use over long periods.

The design of the Poulan 183113 emphasizes ease of maintenance. It features tool-less chain adjustment, making it simple for users to adjust the tension of the chain without the need for specialized tools. This means that operators can achieve the best performance from their chainsaw while ensuring the longevity of the cutting equipment.

In summary, the Poulan 183113 is an efficient chainsaw that combines a powerful engine, advanced starting technology, and thoughtful safety features. With its lightweight design and user-friendly maintenance options, it caters to a wide range of cutting needs, making it an ideal choice for both seasoned professionals and homeowners alike. Users can trust the Poulan 183113 to deliver consistent performance for all their cutting jobs.