Poulan 183113 owner manual Interlocks and Relays, To Replace Fuse, To Adjust Carburetor

Page 25

SERVICE AND ADJUSTMENTS

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 32)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

With engine not running, move throttle control lever to fast position.

Check that swivel is against stop. If it is not, loosen cable clamp screw and pull cable back until swivel is against stop. Tighten cable clamp screw securely.

TO ADJUST CHOKE CONTROL (See Fig. 33)

The choke control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

With engine not running, move choke control (located on dash panel) to full choke position.

Loosen knob and remove cover assembly from air cleaner.

Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely.

Replace air cleaner cover assembly and tighten knob.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

STOP

SWIVELCLAMP

SCREW

FIG. 32

CLAMP SCREW

FIG. 33

25

Image 25
Contents PR185H42STG IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingCheck Deck Levelness To Convert to Bagging or DischargingOperation Motion Control Lever Selects the speed Know Your TractorHOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other Attach Before Starting the EngineMents Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips Service Dates Lubrication ChartCustomer Responsibilities General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine Clean AIR INTAKE/COOLING Areas Clean AIR ScreenCleaning Engine OIL FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Fuse Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PR185H42STG Product no 56 SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsOptional Equipment EngineSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183113 specifications

The Poulan 183113 is a powerful and versatile chainsaw that is designed for both professional and casual users. Known for its durability and performance, this model is suitable for various cutting tasks, from pruning branches to felling trees.

One of the standout features of the Poulan 183113 is its engine, which boasts a robust 18-inch bar and a powerful two-cycle engine. This engine provides a balance of performance and efficiency, delivering enough power to handle tough cutting jobs while still being manageable for operators. Its lightweight design allows for easy handling and maneuverability, making it an excellent choice for extended use.

Equipped with advanced technologies, the Poulan 183113 utilizes an easy-start system that ensures reliable starting even in challenging conditions. This feature saves users time and frustration, allowing them to focus on their tasks rather than struggling with engine troubles. Additionally, the chainsaw employs a high-quality chain that provides smooth cutting action, ensuring precision and efficiency during operation.

Safety is also a priority with the Poulan 183113. It comes with various safety features, including a chain brake that immediately stops the chain when activated, reducing the risk of accidents. Moreover, the anti-vibration system minimizes user fatigue, making it comfortable to use over long periods.

The design of the Poulan 183113 emphasizes ease of maintenance. It features tool-less chain adjustment, making it simple for users to adjust the tension of the chain without the need for specialized tools. This means that operators can achieve the best performance from their chainsaw while ensuring the longevity of the cutting equipment.

In summary, the Poulan 183113 is an efficient chainsaw that combines a powerful engine, advanced starting technology, and thoughtful safety features. With its lightweight design and user-friendly maintenance options, it caters to a wide range of cutting needs, making it an ideal choice for both seasoned professionals and homeowners alike. Users can trust the Poulan 183113 to deliver consistent performance for all their cutting jobs.