Poulan 182080 manual To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

Page 21

SERVICE AND ADJUSTMENTS

TO ADJUST BRAKE (See Fig. 22)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE "ENGAGED"

1-1/2"

NUT "A"

JAM NUT

OPERATING

ARM

FIG. 22

TO REPLACE MOTION DRIVE BELT (See Fig. 23)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

•Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

•Remove belt from stationary idler and clutching idler.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Pull belt toward front of tractor and remove downwards from around engine pulley.

•Install new belt by reversing above procedure.

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSAXLE

PULLEY

FIG. 23

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 24)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 24

TO START ENGINE WITH A WEAK BATTERY (See Fig. 25)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Customer Responsibili- ties section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+)

terminal of each battery, taking care not to short against

21chassis.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. PO14542E IV. Service Safety RulesGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsSteering Wheel Seat Unassembled PartsKeys Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Service Dates Lubrication ChartCustomer Responsibilities General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine BatteryBelts Transaxle CoolingTo Service PRE-CLEANER Clean AIR ScreenTo Service Cartridge Engine Cooling Fins See FigMuffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower see FIGTo Remove Mower see FIG Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Remove Hood and Grill Assembly See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PO14542E Schematic4529 ElectricalKEY Part Description Chassis and Enclosures Repair Parts Drive Transaxle Peerless Model 206-545C Steering Assembly KEY Part NO. NO. Description Engine KEY Part Description Seat Assembly Wheels & Tires DecalsMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty C U M SEH Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

182080 specifications

The Poulan 182080 is a versatile and powerful chainsaw designed for both professional landscapers and DIY enthusiasts. Known for its reliability and efficiency, this model brings a combination of robust features and advanced technology that makes cutting tasks a breeze.

One of the standout features of the Poulan 182080 is its engine. It is equipped with a powerful 18-inch, 42cc two-stroke engine, providing an optimal balance of power and weight. This allows users to saw through dense wood and tackle heavy-duty tasks with minimal effort. The engine is designed for easy starting, which is a common frustration with many other chainsaws. Poulan's innovative starting technology ensures that the chainsaw fires up promptly with a few pulls, saving both time and energy.

The design of the Poulan 182080 is user-centered. It features an ergonomic handle that provides a comfortable grip while reducing vibration. This is especially important for prolonged use, as it minimizes fatigue, allowing users to work longer without discomfort. Additionally, the chainsaw is equipped with an automatic oiler that ensures the chain is continuously lubricated, extending its lifespan and improving performance.

Safety is a priority with the Poulan 182080. It includes several safety features such as a chain brake, which stops the chain in the event of kickback, and a protective guard that shields the user's hands. This makes it suitable for both experienced operators and beginners alike.

The chainsaw is also designed with maintenance in mind. The air filter is easily accessible, allowing for quick cleaning or replacement, which is essential for keeping the chainsaw performing at its best. The tool-less chain tensioning system further simplifies the adjustment process, ensuring the chain remains in optimal condition during operation.

In summary, the Poulan 182080 stands out with its powerful engine, user-friendly design, and a host of safety features. Whether it's for pruning, cutting firewood, or tackling larger jobs, this chainsaw combines efficiency and reliability, making it a valuable tool for any user. Its thoughtful engineering ensures that both performance and safety are paramount, establishing it as a top choice in the competitive chainsaw market.
Top Page Image Contents