Poulan 182080 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Customer Responsibilities section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Customer Responsibilities section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be discon- nected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Customer Respon- sibilities section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL

H O S E , O R T A N K D U R I N G S T O R A G E . A L S O , EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Drain the fuel tank.

•Start the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during stor- age. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Customer Responsibilities section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model NO. PO14542E Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Lubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower see FIGTo Remove Mower see FIG To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO14542EElectrical 4529KEY Part Description Chassis and Enclosures Repair Parts Drive Transaxle Peerless Model 206-545C Steering Assembly KEY Part NO. NO. Description Engine KEY Part Description Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

182080 specifications

The Poulan 182080 is a versatile and powerful chainsaw designed for both professional landscapers and DIY enthusiasts. Known for its reliability and efficiency, this model brings a combination of robust features and advanced technology that makes cutting tasks a breeze.

One of the standout features of the Poulan 182080 is its engine. It is equipped with a powerful 18-inch, 42cc two-stroke engine, providing an optimal balance of power and weight. This allows users to saw through dense wood and tackle heavy-duty tasks with minimal effort. The engine is designed for easy starting, which is a common frustration with many other chainsaws. Poulan's innovative starting technology ensures that the chainsaw fires up promptly with a few pulls, saving both time and energy.

The design of the Poulan 182080 is user-centered. It features an ergonomic handle that provides a comfortable grip while reducing vibration. This is especially important for prolonged use, as it minimizes fatigue, allowing users to work longer without discomfort. Additionally, the chainsaw is equipped with an automatic oiler that ensures the chain is continuously lubricated, extending its lifespan and improving performance.

Safety is a priority with the Poulan 182080. It includes several safety features such as a chain brake, which stops the chain in the event of kickback, and a protective guard that shields the user's hands. This makes it suitable for both experienced operators and beginners alike.

The chainsaw is also designed with maintenance in mind. The air filter is easily accessible, allowing for quick cleaning or replacement, which is essential for keeping the chainsaw performing at its best. The tool-less chain tensioning system further simplifies the adjustment process, ensuring the chain remains in optimal condition during operation.

In summary, the Poulan 182080 stands out with its powerful engine, user-friendly design, and a host of safety features. Whether it's for pruning, cutting firewood, or tackling larger jobs, this chainsaw combines efficiency and reliability, making it a valuable tool for any user. Its thoughtful engineering ensures that both performance and safety are paramount, establishing it as a top choice in the competitive chainsaw market.
Top Page Image Contents