Poulan 182080 manual Troubleshooting Points

Page 25

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

 

CORRECTION

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

4.

Bad spark plug.

4.

Replace spark plug.

 

5.

Dirty air filter.

5.

Clean/replace air filter.

 

6.

Dirty fuel filter.

6.

Replace fuel filter.

 

7.

Water in fuel.

7.

Drain fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

8.

Loose or damaged wiring.

8.

Check all wiring.

 

9.

Carburetor out of adjustment.

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

10.

Engine valves out of adjustment.

10.

Contact an authorized service center/department.

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

2.

Bad spark plug.

2.

Replace spark plug.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

5.

Stale or dirty fuel.

5.

Drain fuel tank and refill with fresh gasoline.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

Engine will not turn over

1.

Clutch/brake pedal not depressed.

1.

Depress clutch/brake pedal.

 

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Blown fuse.

4.

Replace fuse.

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

Engine clicks but will not

1.

Weak or dead battery.

1.

Recharge or replace battery.

start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Set in “Higher Cut” position/reduce speed.

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

3.

Build-up of grass, leaves and trash under mower.

3.

Clean underside of mower housing.

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

8.

Stale or dirty fuel.

8.

Drain fuel tank and refill with fresh gasoline.

 

9.

Water in fuel.

9.

Drain fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

Excessive vibration

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

25

Image 25
Contents Model NO. PO14542E IV. Service Safety RulesGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsSteering Wheel Seat Unassembled PartsKeys Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsADD Gasoline Mowing TipsTo Start Engine See Fig Service Dates Lubrication ChartCustomer Responsibilities General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine BatteryBelts Transaxle CoolingTo Service PRE-CLEANER Clean AIR ScreenTo Service Cartridge Engine Cooling Fins See FigMuffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Install Mower see FIG Service and AdjustmentsTo Remove Mower see FIG Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Remove Hood and Grill Assembly See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PO14542E Schematic4529 ElectricalKEY Part Description Chassis and Enclosures Repair Parts Drive Transaxle Peerless Model 206-545C Steering Assembly KEY Part NO. NO. Description Engine KEY Part Description Seat Assembly Wheels & Tires DecalsMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty C U M SEH Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

182080 specifications

The Poulan 182080 is a versatile and powerful chainsaw designed for both professional landscapers and DIY enthusiasts. Known for its reliability and efficiency, this model brings a combination of robust features and advanced technology that makes cutting tasks a breeze.

One of the standout features of the Poulan 182080 is its engine. It is equipped with a powerful 18-inch, 42cc two-stroke engine, providing an optimal balance of power and weight. This allows users to saw through dense wood and tackle heavy-duty tasks with minimal effort. The engine is designed for easy starting, which is a common frustration with many other chainsaws. Poulan's innovative starting technology ensures that the chainsaw fires up promptly with a few pulls, saving both time and energy.

The design of the Poulan 182080 is user-centered. It features an ergonomic handle that provides a comfortable grip while reducing vibration. This is especially important for prolonged use, as it minimizes fatigue, allowing users to work longer without discomfort. Additionally, the chainsaw is equipped with an automatic oiler that ensures the chain is continuously lubricated, extending its lifespan and improving performance.

Safety is a priority with the Poulan 182080. It includes several safety features such as a chain brake, which stops the chain in the event of kickback, and a protective guard that shields the user's hands. This makes it suitable for both experienced operators and beginners alike.

The chainsaw is also designed with maintenance in mind. The air filter is easily accessible, allowing for quick cleaning or replacement, which is essential for keeping the chainsaw performing at its best. The tool-less chain tensioning system further simplifies the adjustment process, ensuring the chain remains in optimal condition during operation.

In summary, the Poulan 182080 stands out with its powerful engine, user-friendly design, and a host of safety features. Whether it's for pruning, cutting firewood, or tackling larger jobs, this chainsaw combines efficiency and reliability, making it a valuable tool for any user. Its thoughtful engineering ensures that both performance and safety are paramount, establishing it as a top choice in the competitive chainsaw market.