Poulan 182080 Tools Required for Assembly, To Remove Tractor from CAR- TON, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

9/16" wrench

Pliers

(2)

1/2" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 5/16 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 18-22 FT. LBS TORQUE.

Place tabs of steering boot over tab slots in dash and push down to secure.

 

STEERING

 

WHEEL INSERT

 

3/8 HEX BOLT

 

3/8 LOCK WASHER

 

LARGE FLAT

 

WASHER

 

STEERING

STEERING

WHEEL

 

BOOT

 

 

TABS

 

EXTENSION

 

SHAFT

ADAPTER

5/16 HEX BOLT

 

5/16 LOCKNUT

 

LOWER

TAB

STEERING

SLOTS

SHAFT

 

FIG. 1

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large flat washer, 3/8 lock washer, 3/8 hex bolt and tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

6

Image 6
Contents Model NO. PO14542E General Operation Safety RulesIV. Service II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesKeys Unassembled PartsSteering Wheel Seat Slope SheetTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Customer Responsibilities Lubrication ChartService Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower see FIGTo Remove Mower see FIG To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO14542EElectrical 4529KEY Part Description Chassis and Enclosures Repair Parts Drive Transaxle Peerless Model 206-545C Steering Assembly KEY Part NO. NO. Description Engine KEY Part Description Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

182080 specifications

The Poulan 182080 is a versatile and powerful chainsaw designed for both professional landscapers and DIY enthusiasts. Known for its reliability and efficiency, this model brings a combination of robust features and advanced technology that makes cutting tasks a breeze.

One of the standout features of the Poulan 182080 is its engine. It is equipped with a powerful 18-inch, 42cc two-stroke engine, providing an optimal balance of power and weight. This allows users to saw through dense wood and tackle heavy-duty tasks with minimal effort. The engine is designed for easy starting, which is a common frustration with many other chainsaws. Poulan's innovative starting technology ensures that the chainsaw fires up promptly with a few pulls, saving both time and energy.

The design of the Poulan 182080 is user-centered. It features an ergonomic handle that provides a comfortable grip while reducing vibration. This is especially important for prolonged use, as it minimizes fatigue, allowing users to work longer without discomfort. Additionally, the chainsaw is equipped with an automatic oiler that ensures the chain is continuously lubricated, extending its lifespan and improving performance.

Safety is a priority with the Poulan 182080. It includes several safety features such as a chain brake, which stops the chain in the event of kickback, and a protective guard that shields the user's hands. This makes it suitable for both experienced operators and beginners alike.

The chainsaw is also designed with maintenance in mind. The air filter is easily accessible, allowing for quick cleaning or replacement, which is essential for keeping the chainsaw performing at its best. The tool-less chain tensioning system further simplifies the adjustment process, ensuring the chain remains in optimal condition during operation.

In summary, the Poulan 182080 stands out with its powerful engine, user-friendly design, and a host of safety features. Whether it's for pruning, cutting firewood, or tackling larger jobs, this chainsaw combines efficiency and reliability, making it a valuable tool for any user. Its thoughtful engineering ensures that both performance and safety are paramount, establishing it as a top choice in the competitive chainsaw market.