Poulan YTH2148 To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 13

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a fl at level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

019

77

 

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

ATTACHMENT CLUTCH

ATTACHMENT

SWITCH PULL OUT TO

LIFT LEVER HIGH

"ENGAGE"

POSITION

LOW

POSITION

PUSH IN TO "DISENGAGE"

0277

DEFLECTOR

5

SHIELD

FIG. 10

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents YTH2148 IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Mower Unassembled PartsTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonTo Attach Nose Roller See Fig Install Seat See FigAssemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceBefore Each USE Tractor Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement 532 19 18-27 Rev 4.14.04 rad/MH

YTH2148 specifications

The Poulan YTH2148 is a powerful and versatile riding lawn mower designed for homeowners who value efficiency and quality in lawn care. With its robust build and user-friendly features, this tractor stands out as a reliable option for maintaining medium to large-sized lawns.

One of the main features of the YTH2148 is its 21.5 HP Briggs & Stratton engine. This reliable engine provides ample power for tackling tough grass and uneven terrains, ensuring a consistent performance throughout your mowing tasks. Additionally, the easy-start ignition system makes getting the engine running hassle-free, allowing you to start your mowing session with minimal delay.

The cutting deck on the Poulan YTH2148 measures 48 inches in width, making it suitable for covering large areas quickly. The deck is made from durable steel, designed to withstand the rigors of regular use. Furthermore, the mower features a deck lift system that is simple and efficient, allowing you to adjust the cutting height with ease. The cutting height can be set in multiple positions, ranging from 1.5 to 4 inches, enabling you to achieve the perfect cut for your lawn type.

Another notable characteristic of the YTH2148 is its hydrostatic transmission. This advanced technology provides smooth and effortless speed control without the need for manual shifting. This feature is particularly beneficial when navigating around obstacles or making tight turns, as it allows for seamless acceleration and deceleration.

Comfort is also a priority in the design of the Poulan YTH2148. The mower is equipped with an ergonomic seat that provides ample cushioning and back support, ensuring that you can mow for extended periods without discomfort. The wide footrests and easy-to-reach controls further enhance the rider's comfort and ease of operation.

For added convenience, the YTH2148 features a compact design, making it easy to maneuver in tight spaces and around landscaping features. With a turning radius of 16 inches, it can navigate flower beds and garden edges with precision.

Overall, the Poulan YTH2148 combines power, efficiency, and comfort in a well-designed package, making it an exceptional choice for those who take pride in their lawn care. Whether you are a seasoned lawn care expert or a homeowner looking to maintain your yard, the YTH2148 delivers performance and reliability that you can count on.
Top Page Image Contents