Poulan YTH2148 owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert fl anged pins. Secure pins with double loop retainer springs between the plate and mower brack- ets.

NOTE: To assist in locating hole in fl anged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly infl ated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinfl ated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

00598

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 19

SUSPENSION

ARM

01553

LIFT LINK

ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns.The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

BLADE

02548

“B”“B”

FIG. 21

BOTH FRONT PLATE LINKS MUST BE

 

EQUAL IN LENGTH

 

 

02516

 

NUT “D”

 

NUT “C”

 

02517

TRUNNION

 

 

FRONT PLATE

 

 

ASSEMBLY

 

 

FIG. 22

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents YTH2148 IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Mower Unassembled PartsTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Maintenance General RecommendationsBefore Each USE Tractor Engine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement 532 19 18-27 Rev 4.14.04 rad/MH

YTH2148 specifications

The Poulan YTH2148 is a powerful and versatile riding lawn mower designed for homeowners who value efficiency and quality in lawn care. With its robust build and user-friendly features, this tractor stands out as a reliable option for maintaining medium to large-sized lawns.

One of the main features of the YTH2148 is its 21.5 HP Briggs & Stratton engine. This reliable engine provides ample power for tackling tough grass and uneven terrains, ensuring a consistent performance throughout your mowing tasks. Additionally, the easy-start ignition system makes getting the engine running hassle-free, allowing you to start your mowing session with minimal delay.

The cutting deck on the Poulan YTH2148 measures 48 inches in width, making it suitable for covering large areas quickly. The deck is made from durable steel, designed to withstand the rigors of regular use. Furthermore, the mower features a deck lift system that is simple and efficient, allowing you to adjust the cutting height with ease. The cutting height can be set in multiple positions, ranging from 1.5 to 4 inches, enabling you to achieve the perfect cut for your lawn type.

Another notable characteristic of the YTH2148 is its hydrostatic transmission. This advanced technology provides smooth and effortless speed control without the need for manual shifting. This feature is particularly beneficial when navigating around obstacles or making tight turns, as it allows for seamless acceleration and deceleration.

Comfort is also a priority in the design of the Poulan YTH2148. The mower is equipped with an ergonomic seat that provides ample cushioning and back support, ensuring that you can mow for extended periods without discomfort. The wide footrests and easy-to-reach controls further enhance the rider's comfort and ease of operation.

For added convenience, the YTH2148 features a compact design, making it easy to maneuver in tight spaces and around landscaping features. With a turning radius of 16 inches, it can navigate flower beds and garden edges with precision.

Overall, the Poulan YTH2148 combines power, efficiency, and comfort in a well-designed package, making it an exceptional choice for those who take pride in their lawn care. Whether you are a seasoned lawn care expert or a homeowner looking to maintain your yard, the YTH2148 delivers performance and reliability that you can count on.
Top Page Image Contents