Poulan 183368 To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 17

SUSPENSION ARM

LIFT LINK ADJUSTMENT

NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position. Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PPR2042STC Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Hardware Steering Wheel SeatBlades KeysAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsBefore Each USE General Recommendations Lubrication ChartCustomer Responsibilities Tractor Engine Cleaning AIR Filter See FigMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor Model Number PPR2042STCElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly 180656 Wheel Steering Seat Assembly KEY Part NO. NO. DescriptionDecals Wheels and TiresSpark Arrester EngineOptional Equipment 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183368 specifications

The Poulan 183368 is an impressive piece of equipment designed for both home and professional users looking for a reliable chainsaw. Renowned for its robust features and user-friendly design, the Poulan 183368 stands out in its category.

One of the main features of the Poulan 183368 is its powerful engine. Equipped with a 42cc two-cycle engine, this chainsaw delivers ample power for cutting through various types of wood. Whether you're felling trees, cutting firewood, or tackling overgrown branches, the Poulan 183368 can handle the task with ease. Its high torque can be particularly beneficial for those heavier cuts, ensuring efficiency and performance.

Another significant aspect of the Poulan 183368 is its advanced cooling system. This technology helps to maintain engine temperatures, allowing for longer operational periods without overheating. Not only does this enhance the durability of the chainsaw, but it also contributes to better performance during extended use.

The Poulan 183368 features an automatic oiling system that ensures the chain remains lubricated during cutting. This is crucial for maintaining the life of the chain and bar, reducing wear and tear, and enhancing cutting efficiency. Users will appreciate the convenience of not having to manually oil the chain before each use.

Safety is a paramount consideration, and the Poulan 183368 addresses this with several features. It includes a chain brake that stops the chain quickly in case of kickback, providing peace of mind to users. Additionally, the comfortable and ergonomically designed handle allows for better grip and control while operating the chainsaw.

The chainsaw is also equipped with an easy-access air filter, which simplifies maintenance and prolongs the engine's life. This feature makes it easier for users to clean and replace the filter, ensuring optimal engine performance.

In terms of portability and ease of use, the Poulan 183368 is designed to be lightweight, enabling users to maneuver easily while working on various projects. Its compact design makes it an excellent choice for homeowners and professionals alike.

Overall, the Poulan 183368 is a versatile and efficient chainsaw that combines power, safety, and ease of maintenance. It serves as an ideal tool for anyone looking to tackle outdoor cutting tasks with confidence and reliability.
Top Page Image Contents