Poulan 183368 owner manual Off

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves

 

 

 

corrected, contact an authorized service center/

seat with attachment

 

 

 

department.

clutch engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents PPR2042STC General Operation Safety RulesIV. Service II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesBlades Unassembled HardwareSteering Wheel Seat KeysHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsBefore Each USE General Recommendations Lubrication ChartCustomer Responsibilities Tractor Engine Muffler CleaningAIR Filter See Fig Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor Model Number PPR2042STCElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly 180656 Wheel Steering Seat Assembly KEY Part NO. NO. DescriptionDecals Wheels and TiresSpark Arrester EngineOptional Equipment 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183368 specifications

The Poulan 183368 is an impressive piece of equipment designed for both home and professional users looking for a reliable chainsaw. Renowned for its robust features and user-friendly design, the Poulan 183368 stands out in its category.

One of the main features of the Poulan 183368 is its powerful engine. Equipped with a 42cc two-cycle engine, this chainsaw delivers ample power for cutting through various types of wood. Whether you're felling trees, cutting firewood, or tackling overgrown branches, the Poulan 183368 can handle the task with ease. Its high torque can be particularly beneficial for those heavier cuts, ensuring efficiency and performance.

Another significant aspect of the Poulan 183368 is its advanced cooling system. This technology helps to maintain engine temperatures, allowing for longer operational periods without overheating. Not only does this enhance the durability of the chainsaw, but it also contributes to better performance during extended use.

The Poulan 183368 features an automatic oiling system that ensures the chain remains lubricated during cutting. This is crucial for maintaining the life of the chain and bar, reducing wear and tear, and enhancing cutting efficiency. Users will appreciate the convenience of not having to manually oil the chain before each use.

Safety is a paramount consideration, and the Poulan 183368 addresses this with several features. It includes a chain brake that stops the chain quickly in case of kickback, providing peace of mind to users. Additionally, the comfortable and ergonomically designed handle allows for better grip and control while operating the chainsaw.

The chainsaw is also equipped with an easy-access air filter, which simplifies maintenance and prolongs the engine's life. This feature makes it easier for users to clean and replace the filter, ensuring optimal engine performance.

In terms of portability and ease of use, the Poulan 183368 is designed to be lightweight, enabling users to maneuver easily while working on various projects. Its compact design makes it an excellent choice for homeowners and professionals alike.

Overall, the Poulan 183368 is a versatile and efficient chainsaw that combines power, safety, and ease of maintenance. It serves as an ideal tool for anyone looking to tackle outdoor cutting tasks with confidence and reliability.
Top Page Image Contents