Poulan 183368 owner manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

7/16" wrenches

Utility knife

(1)

3/4" wrench

Tire pressure gauge

 

 

Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mount- ing holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

1/2 HEX NUT

LARGE FLAT

WASHER

STEERING

STEERING

WHEEL

BOOT

 

TABS

ADAPTER

 

 

EXTENSION SHAFT

1/4 LOCKNUT

 

 

1/4 HEX BOLT

LOWER

 

STEERING

 

SHAFT

 

 

TAB

 

SLOTS

FIG. 1

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in CUSTOMER RESPONSIBILITIES section of this manual for charging instructions).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PPR2042STC General Operation Safety RulesIV. Service II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesBlades Unassembled HardwareSteering Wheel Seat KeysHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication Chart Customer ResponsibilitiesBefore Each USE Tractor Engine Muffler CleaningAIR Filter See Fig Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor Model Number PPR2042STCElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly 180656 Wheel Steering Seat Assembly KEY Part NO. NO. DescriptionDecals Wheels and TiresEngine Optional EquipmentSpark Arrester 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183368 specifications

The Poulan 183368 is an impressive piece of equipment designed for both home and professional users looking for a reliable chainsaw. Renowned for its robust features and user-friendly design, the Poulan 183368 stands out in its category.

One of the main features of the Poulan 183368 is its powerful engine. Equipped with a 42cc two-cycle engine, this chainsaw delivers ample power for cutting through various types of wood. Whether you're felling trees, cutting firewood, or tackling overgrown branches, the Poulan 183368 can handle the task with ease. Its high torque can be particularly beneficial for those heavier cuts, ensuring efficiency and performance.

Another significant aspect of the Poulan 183368 is its advanced cooling system. This technology helps to maintain engine temperatures, allowing for longer operational periods without overheating. Not only does this enhance the durability of the chainsaw, but it also contributes to better performance during extended use.

The Poulan 183368 features an automatic oiling system that ensures the chain remains lubricated during cutting. This is crucial for maintaining the life of the chain and bar, reducing wear and tear, and enhancing cutting efficiency. Users will appreciate the convenience of not having to manually oil the chain before each use.

Safety is a paramount consideration, and the Poulan 183368 addresses this with several features. It includes a chain brake that stops the chain quickly in case of kickback, providing peace of mind to users. Additionally, the comfortable and ergonomically designed handle allows for better grip and control while operating the chainsaw.

The chainsaw is also equipped with an easy-access air filter, which simplifies maintenance and prolongs the engine's life. This feature makes it easier for users to clean and replace the filter, ensuring optimal engine performance.

In terms of portability and ease of use, the Poulan 183368 is designed to be lightweight, enabling users to maneuver easily while working on various projects. Its compact design makes it an excellent choice for homeowners and professionals alike.

Overall, the Poulan 183368 is a versatile and efficient chainsaw that combines power, safety, and ease of maintenance. It serves as an ideal tool for anyone looking to tackle outdoor cutting tasks with confidence and reliability.
Top Page Image Contents