Poulan 183368 owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 29)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 29

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever to fast position.

•Check that swivel is against stop. If it is not, loosen cable clamp screw and pull cable back until swivel is against stop. Tighten cable clamp screw securely.

TO ADJUST CHOKE CONTROL (See Fig. 31)

The choke control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move choke control (located on dash panel) to full choke position.

•Loosen knob and remove cover assembly from air cleaner.

•Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely.

•Replace air cleaner cover assembly and tighten knob.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

STOP

CLAMP

SWIVELSCREW

FIG. 30

CLAMP SCREW

FIG. 31

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PPR2042STC II. Slope Operation Safety RulesIV. Service General OperationTable of Contents Customer Responsibilities Product SpecificationsKeys Unassembled HardwareSteering Wheel Seat BladesTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Transport To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsBefore Each USE General Recommendations Lubrication ChartCustomer Responsibilities Tractor Engine Spark Plugs CleaningAIR Filter See Fig MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsOFF Tractor Model Number PPR2042STC SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive 175410 Pulley Eng Steering Assembly 180656 Wheel Steering KEY Part NO. NO. Description Seat AssemblyWheels and Tires DecalsSpark Arrester EngineOptional Equipment 170771 Control Throt Mower Deck Washer, Spacer Mower Vented Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Service Notes C U M SEH Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183368 specifications

The Poulan 183368 is an impressive piece of equipment designed for both home and professional users looking for a reliable chainsaw. Renowned for its robust features and user-friendly design, the Poulan 183368 stands out in its category.

One of the main features of the Poulan 183368 is its powerful engine. Equipped with a 42cc two-cycle engine, this chainsaw delivers ample power for cutting through various types of wood. Whether you're felling trees, cutting firewood, or tackling overgrown branches, the Poulan 183368 can handle the task with ease. Its high torque can be particularly beneficial for those heavier cuts, ensuring efficiency and performance.

Another significant aspect of the Poulan 183368 is its advanced cooling system. This technology helps to maintain engine temperatures, allowing for longer operational periods without overheating. Not only does this enhance the durability of the chainsaw, but it also contributes to better performance during extended use.

The Poulan 183368 features an automatic oiling system that ensures the chain remains lubricated during cutting. This is crucial for maintaining the life of the chain and bar, reducing wear and tear, and enhancing cutting efficiency. Users will appreciate the convenience of not having to manually oil the chain before each use.

Safety is a paramount consideration, and the Poulan 183368 addresses this with several features. It includes a chain brake that stops the chain quickly in case of kickback, providing peace of mind to users. Additionally, the comfortable and ergonomically designed handle allows for better grip and control while operating the chainsaw.

The chainsaw is also equipped with an easy-access air filter, which simplifies maintenance and prolongs the engine's life. This feature makes it easier for users to clean and replace the filter, ensuring optimal engine performance.

In terms of portability and ease of use, the Poulan 183368 is designed to be lightweight, enabling users to maneuver easily while working on various projects. Its compact design makes it an excellent choice for homeowners and professionals alike.

Overall, the Poulan 183368 is a versatile and efficient chainsaw that combines power, safety, and ease of maintenance. It serves as an ideal tool for anyone looking to tackle outdoor cutting tasks with confidence and reliability.
Top Page Image Contents