Poulan 191984 manual Engine

Page 17

MAINTENANCE

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

Rinse the battery with plain water and dry.

Clean terminals and battery cable ends with wire brush until bright.

Coat terminals with grease or petroleum jelly.

Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

The transmission fan and cooling fins should be kept clean to assure proper cooling.

Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent pos- sible damage to seals, do not use high pressure water or steam to clean transaxle.

Inspect cooling fan to be sure fan blades are intact and clean.

Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cool- ing fins.

TRANSAXLE PUMP FLUID

The transaxle was sealed at the factory and fluid mainte- nance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

oil_visc_chart1_e

FIG. 11

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the tractor is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Figs. 11 and 12)

Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ.

Be sure tractor is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

Remove yellow cap from end of drain valve and install the drain tube onto the fitting.

OIL DRAIN VALVE

CLOSED AND

LOCKED

POSITION

YELLOW CAP

DRAIN

TUBE

02463

FIG. 12

Unlock drain valve by pushing inward and turning counterclockwise.

To open, pull out on the drain valve.

After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve.

Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this man- ual.

Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.Tighten cap onto the tube securely when finished.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

17

Image 17
Contents Model NO. PO175H42STB Safety Rules Safety Rules Table of Contents Steering Wheel Seat Unassembled PartsKey Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Before Starting the EngineTo Transport See Figs To Operate on HillsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine AIR Filter CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

191984 specifications

The Poulan 191984 is a powerful and versatile chainsaw that stands out in the realm of outdoor tools. Designed for homeowners and professionals alike, the 191984 is engineered to provide robust performance and user-friendly features, making it an ideal choice for a variety of cutting tasks.

One of the key features of the Poulan 191984 is its efficient engine. The chainsaw is equipped with a reliable 42cc two-stroke engine, delivering ample power for cutting through tough wood with ease. This engine is designed for maximum efficiency, providing excellent fuel economy while maintaining high performance. As a result, users can expect longer operating times between refuels, which is particularly beneficial for those large projects that require sustained cutting.

The Poulan 191984 also incorporates advanced technologies that enhance its usability. A notable feature is its Easy Start technology, which significantly reduces the effort needed to start the chainsaw. This feature is especially valuable for those who may struggle with traditional pull-start mechanisms. Additionally, the chainsaw is equipped with a primer bulb that ensures an easier starting procedure, allowing users to get to work quickly without unnecessary hassle.

Another highlight of the 191984 is its cutting capacity. The chainsaw boasts a 16-inch bar and chain, providing a good balance for various cutting applications, including tree trimming, firewood preparation, and light to medium-duty logging tasks. The design allows for effective cuts while remaining manageable, giving users both power and control.

Safety is a critical consideration in the design of the Poulan 191984. It features a chain brake, which helps prevent accidental chain rotation during operation and contributes to safer handling. The ergonomic handle design ensures comfort during use, reducing fatigue and enhancing control. Additionally, the chainsaw is lightweight, making it easy to maneuver even during extended use.

Maintenance has also been simplified with the Poulan 191984. The tool-free chain tensioning system allows users to adjust the chain tension without the need for additional tools, making adjustments straightforward and quick. The transparent fuel and oil tanks provide visibility into levels, helping users manage their fuel efficiently.

Overall, the Poulan 191984 combines power, efficiency, and safety features that make it a reliable choice for anyone looking for a dependable chainsaw. Whether for homeowners or seasoned professionals, its balanced performance and user-centric design ensure it meets the demands of various cutting tasks effectively.