Poulan 191984 manual HOW to SET UP Your Tractor, Install Seat See Fig, Check Battery See Fig

Page 7

ASSEMBLY

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

SEAT

SEAT PAN

SHOULDER

BOLT

02466

FLAT WASHER

LOCK WASHER

02465

ADJUSTMENT

BOLT

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model NO. PO175H42STB Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeyBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Operate Mower See Fig To Transport See FigsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Spark Plugs CleaningAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

191984 specifications

The Poulan 191984 is a powerful and versatile chainsaw that stands out in the realm of outdoor tools. Designed for homeowners and professionals alike, the 191984 is engineered to provide robust performance and user-friendly features, making it an ideal choice for a variety of cutting tasks.

One of the key features of the Poulan 191984 is its efficient engine. The chainsaw is equipped with a reliable 42cc two-stroke engine, delivering ample power for cutting through tough wood with ease. This engine is designed for maximum efficiency, providing excellent fuel economy while maintaining high performance. As a result, users can expect longer operating times between refuels, which is particularly beneficial for those large projects that require sustained cutting.

The Poulan 191984 also incorporates advanced technologies that enhance its usability. A notable feature is its Easy Start technology, which significantly reduces the effort needed to start the chainsaw. This feature is especially valuable for those who may struggle with traditional pull-start mechanisms. Additionally, the chainsaw is equipped with a primer bulb that ensures an easier starting procedure, allowing users to get to work quickly without unnecessary hassle.

Another highlight of the 191984 is its cutting capacity. The chainsaw boasts a 16-inch bar and chain, providing a good balance for various cutting applications, including tree trimming, firewood preparation, and light to medium-duty logging tasks. The design allows for effective cuts while remaining manageable, giving users both power and control.

Safety is a critical consideration in the design of the Poulan 191984. It features a chain brake, which helps prevent accidental chain rotation during operation and contributes to safer handling. The ergonomic handle design ensures comfort during use, reducing fatigue and enhancing control. Additionally, the chainsaw is lightweight, making it easy to maneuver even during extended use.

Maintenance has also been simplified with the Poulan 191984. The tool-free chain tensioning system allows users to adjust the chain tension without the need for additional tools, making adjustments straightforward and quick. The transparent fuel and oil tanks provide visibility into levels, helping users manage their fuel efficiently.

Overall, the Poulan 191984 combines power, efficiency, and safety features that make it a reliable choice for anyone looking for a dependable chainsaw. Whether for homeowners or seasoned professionals, its balanced performance and user-centric design ensure it meets the demands of various cutting tasks effectively.
Top Page Image Contents