Poulan 191984 manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 22

SERVICE AND ADJUSTMENTS

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

LEVER NEUTRAL LOCK GATE

ADJUSTMENT

BOLT

02239

FIG. 22

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL

ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 23)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 23

TO START ENGINE WITH A WEAK BATTERY (See Fig. 24)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR DEAD BATTERY FULLY CHARGED BATTERY

FIG. 24

REPLACING BATTERY (See Figs. 25 and 26)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model NO. PO175H42STB Safety Rules Safety Rules Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs Before Starting the EngineTo Operate Mower See Fig To Operate on HillsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Muffler CleaningAIR Filter Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

191984 specifications

The Poulan 191984 is a powerful and versatile chainsaw that stands out in the realm of outdoor tools. Designed for homeowners and professionals alike, the 191984 is engineered to provide robust performance and user-friendly features, making it an ideal choice for a variety of cutting tasks.

One of the key features of the Poulan 191984 is its efficient engine. The chainsaw is equipped with a reliable 42cc two-stroke engine, delivering ample power for cutting through tough wood with ease. This engine is designed for maximum efficiency, providing excellent fuel economy while maintaining high performance. As a result, users can expect longer operating times between refuels, which is particularly beneficial for those large projects that require sustained cutting.

The Poulan 191984 also incorporates advanced technologies that enhance its usability. A notable feature is its Easy Start technology, which significantly reduces the effort needed to start the chainsaw. This feature is especially valuable for those who may struggle with traditional pull-start mechanisms. Additionally, the chainsaw is equipped with a primer bulb that ensures an easier starting procedure, allowing users to get to work quickly without unnecessary hassle.

Another highlight of the 191984 is its cutting capacity. The chainsaw boasts a 16-inch bar and chain, providing a good balance for various cutting applications, including tree trimming, firewood preparation, and light to medium-duty logging tasks. The design allows for effective cuts while remaining manageable, giving users both power and control.

Safety is a critical consideration in the design of the Poulan 191984. It features a chain brake, which helps prevent accidental chain rotation during operation and contributes to safer handling. The ergonomic handle design ensures comfort during use, reducing fatigue and enhancing control. Additionally, the chainsaw is lightweight, making it easy to maneuver even during extended use.

Maintenance has also been simplified with the Poulan 191984. The tool-free chain tensioning system allows users to adjust the chain tension without the need for additional tools, making adjustments straightforward and quick. The transparent fuel and oil tanks provide visibility into levels, helping users manage their fuel efficiently.

Overall, the Poulan 191984 combines power, efficiency, and safety features that make it a reliable choice for anyone looking for a dependable chainsaw. Whether for homeowners or seasoned professionals, its balanced performance and user-centric design ensure it meets the demands of various cutting tasks effectively.
Top Page Image Contents