Poulan 191984 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in con- tact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 14)

Mower will be easier to remove from the right side of trac- tor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and remove clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

TO INSTALL MOWER (See Fig. 14)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with deflector shield to right side of tractor.

•Lower lift lever to its lowest position.

•Connect front links to mower deck and secure with retainer springs..

•Connect suspension arms to rear deck brackets and secure with retainer springs.

•Connect anti-swaybar to chassis bracket and secure with retainer spring.

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE HOLE IN FRAME.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

 

SMALL RETAINER SPRING

 

 

CLUTCH SPRING

 

 

 

FLAT WASHER

 

SQUARE HOLE

SMALL RETAINER SPRING

SUSPENSION

ENGINE PULLEY

 

 

CLUTCH SPRING

ARMS

 

 

 

 

 

 

FRONT LINK

RETAINER SPRING

 

 

 

ANTI-SWAY BAR

 

 

 

 

 

 

RETAINER SPRING

COLLAR

 

 

(BOTH SIDES)

HOUSING GUIDE

LARGE RETAINER SPRING

 

 

 

BRACKET

 

 

 

DEFLECTOR SHIELD

 

 

 

FIG. 14

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model NO. PO175H42STB Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeyBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Operate Mower See Fig To Transport See FigsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Spark Plugs CleaningAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWith attachment clutch Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

191984 specifications

The Poulan 191984 is a powerful and versatile chainsaw that stands out in the realm of outdoor tools. Designed for homeowners and professionals alike, the 191984 is engineered to provide robust performance and user-friendly features, making it an ideal choice for a variety of cutting tasks.

One of the key features of the Poulan 191984 is its efficient engine. The chainsaw is equipped with a reliable 42cc two-stroke engine, delivering ample power for cutting through tough wood with ease. This engine is designed for maximum efficiency, providing excellent fuel economy while maintaining high performance. As a result, users can expect longer operating times between refuels, which is particularly beneficial for those large projects that require sustained cutting.

The Poulan 191984 also incorporates advanced technologies that enhance its usability. A notable feature is its Easy Start technology, which significantly reduces the effort needed to start the chainsaw. This feature is especially valuable for those who may struggle with traditional pull-start mechanisms. Additionally, the chainsaw is equipped with a primer bulb that ensures an easier starting procedure, allowing users to get to work quickly without unnecessary hassle.

Another highlight of the 191984 is its cutting capacity. The chainsaw boasts a 16-inch bar and chain, providing a good balance for various cutting applications, including tree trimming, firewood preparation, and light to medium-duty logging tasks. The design allows for effective cuts while remaining manageable, giving users both power and control.

Safety is a critical consideration in the design of the Poulan 191984. It features a chain brake, which helps prevent accidental chain rotation during operation and contributes to safer handling. The ergonomic handle design ensures comfort during use, reducing fatigue and enhancing control. Additionally, the chainsaw is lightweight, making it easy to maneuver even during extended use.

Maintenance has also been simplified with the Poulan 191984. The tool-free chain tensioning system allows users to adjust the chain tension without the need for additional tools, making adjustments straightforward and quick. The transparent fuel and oil tanks provide visibility into levels, helping users manage their fuel efficiently.

Overall, the Poulan 191984 combines power, efficiency, and safety features that make it a reliable choice for anyone looking for a dependable chainsaw. Whether for homeowners or seasoned professionals, its balanced performance and user-centric design ensure it meets the demands of various cutting tasks effectively.
Top Page Image Contents