Poulan 197022 manual Mowing Tips, Purge Transmission

Page 14

OPERATION

•The attachments can also be used during the engine warm-up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly dis- engage clutch/brake pedal.

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the mo- tion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 8).

FIG. 8

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PO175H42ST Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionService Dates MaintenanceLubrication Chart General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

197022 specifications

The Poulan 197022 is a robust and reliable chainsaw designed for both homeowners and professionals alike. Known for its powerful performance and innovative features, the 197022 stands out in the competitive market of outdoor tools. This model is particularly favored for its versatility, making it suitable for a variety of tasks ranging from trimming branches to felling trees.

One of the main features of the Poulan 197022 is its powerful engine. Equipped with a 50cc two-stroke engine, this chainsaw delivers impressive power for demanding cutting jobs. The engine's design optimizes fuel efficiency, ensuring that users can complete tasks without frequent refueling. This characteristic is essential for large-scale projects, where time and fuel consumption are critical considerations.

The Poulan 197022 also boasts an 18-inch cutting bar, which provides an ideal balance between maneuverability and cutting capacity. This length allows for efficient cutting through a wide range of materials while maintaining ease of use for the operator. The chainsaw’s Oregon chain contributes to smooth and effective cutting performance, ensuring that users achieve clean cuts with minimal effort.

In terms of technology, the Poulan 197022 features an advanced air filtration system that ensures prolonged engine life by keeping dust and debris from entering the engine. This system is crucial for maintaining optimal performance and reducing maintenance needs. Additionally, the chainsaw incorporates an automatic oiling system that delivers consistent lubrication to the blade, further enhancing durability and performance.

Safety is a priority with the Poulan 197022. It includes several safety features such as a chain brake that activates instantly to prevent accidents in case of kickback. The anti-vibration technology used in this model significantly reduces operator fatigue by minimizing the vibrations felt during operation. This feature is particularly beneficial for users who may spend extended periods cutting wood.

Overall, the Poulan 197022 is designed for ease of use and user comfort. Its lightweight design and ergonomic handle ensure that it is accessible for users of all experience levels. Whether for light yard work or heavy-duty cutting, the Poulan 197022 is a standout choice, combining power, efficiency, and safety in one dependable chainsaw.
Top Page Image Contents