Poulan 197022 manual To Check and Adjust Brake, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO CHECK AND ADJUST BRAKE

(See Fig. 20)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and en- gage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16”

JAM NUT

 

OPERATING

ARM

01513

DO NOT TOUCH THIS NUT. IF FURTHER

BRAKE ADJUSTMENT IS NECESSARY CON-

TACT YOUR NEAREST AUTHORIZED SERVICE

CENTER/DEPARTMENT

FIG. 20

TO REPLACE MOTION DRIVE BELT (See Fig. 21)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEYCENTER SPAN KEEPER

FIG. 21

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 22)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine

21 off.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Always Wear EYE Protection During Operation PO175H42STSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsLubrication Chart MaintenanceService Dates General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning To Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust BrakeSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

197022 specifications

The Poulan 197022 is a robust and reliable chainsaw designed for both homeowners and professionals alike. Known for its powerful performance and innovative features, the 197022 stands out in the competitive market of outdoor tools. This model is particularly favored for its versatility, making it suitable for a variety of tasks ranging from trimming branches to felling trees.

One of the main features of the Poulan 197022 is its powerful engine. Equipped with a 50cc two-stroke engine, this chainsaw delivers impressive power for demanding cutting jobs. The engine's design optimizes fuel efficiency, ensuring that users can complete tasks without frequent refueling. This characteristic is essential for large-scale projects, where time and fuel consumption are critical considerations.

The Poulan 197022 also boasts an 18-inch cutting bar, which provides an ideal balance between maneuverability and cutting capacity. This length allows for efficient cutting through a wide range of materials while maintaining ease of use for the operator. The chainsaw’s Oregon chain contributes to smooth and effective cutting performance, ensuring that users achieve clean cuts with minimal effort.

In terms of technology, the Poulan 197022 features an advanced air filtration system that ensures prolonged engine life by keeping dust and debris from entering the engine. This system is crucial for maintaining optimal performance and reducing maintenance needs. Additionally, the chainsaw incorporates an automatic oiling system that delivers consistent lubrication to the blade, further enhancing durability and performance.

Safety is a priority with the Poulan 197022. It includes several safety features such as a chain brake that activates instantly to prevent accidents in case of kickback. The anti-vibration technology used in this model significantly reduces operator fatigue by minimizing the vibrations felt during operation. This feature is particularly beneficial for users who may spend extended periods cutting wood.

Overall, the Poulan 197022 is designed for ease of use and user comfort. Its lightweight design and ergonomic handle ensure that it is accessible for users of all experience levels. Whether for light yard work or heavy-duty cutting, the Poulan 197022 is a standout choice, combining power, efficiency, and safety in one dependable chainsaw.
Top Page Image Contents