Poulan 197022 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVERTRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PO175H42ST Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System To Operate Mower See FigReverse Operation System ROS To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance Lubrication ChartService Dates General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigSee Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

197022 specifications

The Poulan 197022 is a robust and reliable chainsaw designed for both homeowners and professionals alike. Known for its powerful performance and innovative features, the 197022 stands out in the competitive market of outdoor tools. This model is particularly favored for its versatility, making it suitable for a variety of tasks ranging from trimming branches to felling trees.

One of the main features of the Poulan 197022 is its powerful engine. Equipped with a 50cc two-stroke engine, this chainsaw delivers impressive power for demanding cutting jobs. The engine's design optimizes fuel efficiency, ensuring that users can complete tasks without frequent refueling. This characteristic is essential for large-scale projects, where time and fuel consumption are critical considerations.

The Poulan 197022 also boasts an 18-inch cutting bar, which provides an ideal balance between maneuverability and cutting capacity. This length allows for efficient cutting through a wide range of materials while maintaining ease of use for the operator. The chainsaw’s Oregon chain contributes to smooth and effective cutting performance, ensuring that users achieve clean cuts with minimal effort.

In terms of technology, the Poulan 197022 features an advanced air filtration system that ensures prolonged engine life by keeping dust and debris from entering the engine. This system is crucial for maintaining optimal performance and reducing maintenance needs. Additionally, the chainsaw incorporates an automatic oiling system that delivers consistent lubrication to the blade, further enhancing durability and performance.

Safety is a priority with the Poulan 197022. It includes several safety features such as a chain brake that activates instantly to prevent accidents in case of kickback. The anti-vibration technology used in this model significantly reduces operator fatigue by minimizing the vibrations felt during operation. This feature is particularly beneficial for users who may spend extended periods cutting wood.

Overall, the Poulan 197022 is designed for ease of use and user comfort. Its lightweight design and ergonomic handle ensure that it is accessible for users of all experience levels. Whether for light yard work or heavy-duty cutting, the Poulan 197022 is a standout choice, combining power, efficiency, and safety in one dependable chainsaw.
Top Page Image Contents