Poulan 197022 manual Cleaning

Page 18

MAINTENANCE

•Unlock drain valve by pushing inward and turning counterclockwise.

•To open, pull out on the drain valve.

•After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

•Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve.

•Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this man- ual.

•Use gauge on oil fill cap/dipstick for checking level. For accurate reading, insert dipstick into the tube and push down firmly into place before removing. Keep oil up to, but not over, the “FULL” line on dip- stick. Push dipstick down firmly into the tube when finished.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

AIR FILTER

Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See Engine Manual.

ENGINE OIL FILTER

Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year.

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 13)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

•With engine cool, remove filter and plug fuel line sec- tions.

•Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

•Be sure there are no fuel line leaks and clamps are properly positioned.

•Immediately wipe up any spilled gasoline.

CLAMP

CLAMP

FUEL FILTER

FIG. 13

CLEANING

•Clean engine, battery, seat, finish, etc. of all foreign matter.

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PO175H42ST Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionService Dates MaintenanceLubrication Chart General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

197022 specifications

The Poulan 197022 is a robust and reliable chainsaw designed for both homeowners and professionals alike. Known for its powerful performance and innovative features, the 197022 stands out in the competitive market of outdoor tools. This model is particularly favored for its versatility, making it suitable for a variety of tasks ranging from trimming branches to felling trees.

One of the main features of the Poulan 197022 is its powerful engine. Equipped with a 50cc two-stroke engine, this chainsaw delivers impressive power for demanding cutting jobs. The engine's design optimizes fuel efficiency, ensuring that users can complete tasks without frequent refueling. This characteristic is essential for large-scale projects, where time and fuel consumption are critical considerations.

The Poulan 197022 also boasts an 18-inch cutting bar, which provides an ideal balance between maneuverability and cutting capacity. This length allows for efficient cutting through a wide range of materials while maintaining ease of use for the operator. The chainsaw’s Oregon chain contributes to smooth and effective cutting performance, ensuring that users achieve clean cuts with minimal effort.

In terms of technology, the Poulan 197022 features an advanced air filtration system that ensures prolonged engine life by keeping dust and debris from entering the engine. This system is crucial for maintaining optimal performance and reducing maintenance needs. Additionally, the chainsaw incorporates an automatic oiling system that delivers consistent lubrication to the blade, further enhancing durability and performance.

Safety is a priority with the Poulan 197022. It includes several safety features such as a chain brake that activates instantly to prevent accidents in case of kickback. The anti-vibration technology used in this model significantly reduces operator fatigue by minimizing the vibrations felt during operation. This feature is particularly beneficial for users who may spend extended periods cutting wood.

Overall, the Poulan 197022 is designed for ease of use and user comfort. Its lightweight design and ergonomic handle ensure that it is accessible for users of all experience levels. Whether for light yard work or heavy-duty cutting, the Poulan 197022 is a standout choice, combining power, efficiency, and safety in one dependable chainsaw.
Top Page Image Contents