Poulan 197053 Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable fi rst from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

FIG. 23

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PD15538LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

197053 specifications

The Poulan 197053 is a standout model in the realm of outdoor power equipment, designed specifically for those who demand efficiency, reliability, and effectiveness for their lawn care and landscaping tasks. This model showcases an array of features and technologies that make it an ideal choice for both residential and professional use.

At the heart of the Poulan 197053 is its powerful engine. The machine is equipped with a robust 46cc two-stroke engine that delivers potent cutting power. This engine provides the necessary torque to tackle a variety of tasks, from trimming grass and hedges to more demanding clearing projects. The advanced engine technology not only ensures reliable performance but also promotes fuel efficiency, allowing users to complete jobs without frequent refueling.

One of the key characteristics of the Poulan 197053 is its user-friendly design. Weighing in at a manageable size, this model is built for ease of use. It features an ergonomic handle that provides comfort during prolonged periods of operation, reducing fatigue and enhancing the overall user experience. The lightweight construction ensures that the machine can easily be maneuvered, making it ideal for both small and large outdoor spaces.

In terms of cutting performance, the Poulan 197053 boasts a durable cutting blade that is designed for precision and longevity. The sharp blade ensures a clean cut, promoting the health of your plants and grass. Furthermore, the model offers adjustable height settings, allowing users to customize their cutting experience according to the specific requirements of their lawn or garden.

Technology plays a crucial role in the performance of the Poulan 197053. The model incorporates features such as an automatic oiling system, which ensures that the cutting blade remains adequately lubricated, thereby extending its lifespan and minimizing maintenance needs. The quick-release air filter also promotes easy access for cleaning and replacement, ensuring optimal engine performance over time.

Durability is another hallmark of the Poulan 197053. Constructed with high-quality materials, it is designed to withstand the rigors of outdoor use. The rugged build not only provides longevity but also enhances the effectiveness of the machine in diverse working conditions.

In conclusion, the Poulan 197053 is an exceptional choice for anyone seeking a reliable, feature-rich outdoor power tool. With its powerful engine, ergonomic design, advanced technology, and robust construction, it stands out as a top contender in the garden equipment market. Whether you are a homeowner maintaining your yard or a professional landscaper, this model offers the performance you need to achieve stunning results.
Top Page Image Contents