Poulan 197053 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable fi rst then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 24

TERMINAL

KEPS NUT

COVER

 

HEX

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 25

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

01536

FIG. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Always Wear EYE Protection During Operation PD15538LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport Reverse Operation System ROSTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Transaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

197053 specifications

The Poulan 197053 is a standout model in the realm of outdoor power equipment, designed specifically for those who demand efficiency, reliability, and effectiveness for their lawn care and landscaping tasks. This model showcases an array of features and technologies that make it an ideal choice for both residential and professional use.

At the heart of the Poulan 197053 is its powerful engine. The machine is equipped with a robust 46cc two-stroke engine that delivers potent cutting power. This engine provides the necessary torque to tackle a variety of tasks, from trimming grass and hedges to more demanding clearing projects. The advanced engine technology not only ensures reliable performance but also promotes fuel efficiency, allowing users to complete jobs without frequent refueling.

One of the key characteristics of the Poulan 197053 is its user-friendly design. Weighing in at a manageable size, this model is built for ease of use. It features an ergonomic handle that provides comfort during prolonged periods of operation, reducing fatigue and enhancing the overall user experience. The lightweight construction ensures that the machine can easily be maneuvered, making it ideal for both small and large outdoor spaces.

In terms of cutting performance, the Poulan 197053 boasts a durable cutting blade that is designed for precision and longevity. The sharp blade ensures a clean cut, promoting the health of your plants and grass. Furthermore, the model offers adjustable height settings, allowing users to customize their cutting experience according to the specific requirements of their lawn or garden.

Technology plays a crucial role in the performance of the Poulan 197053. The model incorporates features such as an automatic oiling system, which ensures that the cutting blade remains adequately lubricated, thereby extending its lifespan and minimizing maintenance needs. The quick-release air filter also promotes easy access for cleaning and replacement, ensuring optimal engine performance over time.

Durability is another hallmark of the Poulan 197053. Constructed with high-quality materials, it is designed to withstand the rigors of outdoor use. The rugged build not only provides longevity but also enhances the effectiveness of the machine in diverse working conditions.

In conclusion, the Poulan 197053 is an exceptional choice for anyone seeking a reliable, feature-rich outdoor power tool. With its powerful engine, ergonomic design, advanced technology, and robust construction, it stands out as a top contender in the garden equipment market. Whether you are a homeowner maintaining your yard or a professional landscaper, this model offers the performance you need to achieve stunning results.
Top Page Image Contents